Dleo332w Parts

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

For complete assembly for easier installation order WP37001287

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

This idler assembly is the spring-loaded belt tensioner that keeps the drive belt correctly tightened. Replacing a worn or seized idler restores smooth belt tracking, reduces squeal, and helps prevent slippage or loss of drive.

• Maintains proper tension on the drive belt for reliable power transfer
• Helps prevent belt slippage, squealing, or the belt coming off the pulleys
• Supports smooth rotation of the driven components
• Failure symptoms can include noise from the belt path, a frayed or derailed belt, or loss of motion

• Disconnect power and allow all moving parts to stop before servicing
• Access the belt path; relieve belt tension and remove the old idler assembly
• Install the new assembly; ensure the pulley spins freely and the belt is centered in the groove
• Manually rotate the system to verify alignment and clearances before restoring power

This replacement idler pulley keeps the drive belt tight and tracking correctly so the drum can rotate smoothly. It restores quiet, consistent operation when the original pulley is worn or seized and causing belt slippage or noise.

• Maintains proper tension on the drive belt to enable smooth drum rotation
• Provides a low-friction surface for the belt to ride on and stay aligned
• Common symptoms of failure: squealing/chirping, belt fraying or coming off, burning rubber smell, or a drum that won't turn
• Replace if the pulley wobbles, binds, or the rim/bearing is worn

• Disconnect power; if gas, shut off the gas supply
• Note belt routing, relieve tension from the idler arm, and remove the belt from the motor pulley
• Remove the retaining hardware from the old pulley, install the new pulley on the idler arm shaft, and re-tension the belt
• Manually rotate the drum to verify smooth belt tracking before reassembly and test run

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

Replacement filter cover that secures the appliance's filter inside its housing, protecting the filter and restoring a proper fit. Installs quickly to help prevent debris or accidental contact with the filter media. What it does:

• Secures and protects the filter so it stays properly seated during normal operation.
• Helps keep debris and contaminants out of the filter chamber.
• Replace if the cover is cracked, warped, missing, or the filter no longer latches securely.
• Can help address issues caused by a loose or damaged cover (poor filter seating, intermittent leaks, or rattling).

• Disconnect power before servicing; shut off the water supply if replacing a cover on a water-handling assembly.
• Remove the old cover by releasing the latch or removing fasteners, then align and snap or fasten the replacement into place.
• Inspect the surrounding seal or gasket and replace if worn to ensure a proper seal.
• Test the appliance briefly after installation and check for secure fit and any leaks.

This safety cover is an internal protective shield used inside the dryer to guard components and help maintain proper airflow. Replacing a cracked or missing cover helps keep wiring and moving parts enclosed for safer operation. What it does:

• Shields internal wiring and components from accidental contact
• Helps channel air and lint flow as designed
• Replaces a damaged, heat-warped, or missing cover
• Helps resolve rattling/vibration noises and visible gaps where the cover mounts

• Includes 1 safety cover

• Unplug the dryer; for gas models, shut off gas and allow the unit to cool
• Access the cover location per your model's service manual; remove panels as needed
• Position the cover correctly and secure using existing hardware/clips
• Do not operate the dryer with the cover removed or loose

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

A high-limit thermostat that stops the dryer's heating circuit if internal temperatures get too high, helping prevent overheating and protecting heating components. Replaces a failed high-limit thermostat to restore overheat protection. What it does

• Opens the heating circuit when dryer temperature exceeds the thermostat set point to prevent overheating.
• Commonly related symptoms: dryer runs but produces little or no heat, dryer gets unusually hot, or the thermal cutoff repeatedly fails.
• Works as part of the dryer's temperature-safety system to protect heating elements, fuses, and internal wiring.

• One high-limit thermostat

• Disconnect power before accessing the dryer and work only after panels are cool.
• Take a photo or label wires before removal to ensure correct reconnection.
• Test the thermostat for continuity with a multimeter to confirm failure before replacing.
• If other safety devices (thermal fuse, cycling thermostat, element) show symptoms, inspect and test those components too.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This factory kit reconfigures your dryer's exhaust to exit from the side or bottom instead of the rear. It's ideal for tight installations or when the wall vent location requires an alternate exhaust path. What it does:

• Redirects the exhaust outlet to the left, right, or bottom on compatible models (orientation varies by model)
• Enables installation in closets or shallow spaces where rear venting isn't practical
• Replaces missing or damaged side/bottom vent hardware
• Helps maintain a proper metal exhaust path when relocating the dryer

• One side vent kit

• Disconnect electrical power and shut off gas supply (if applicable) before starting
• Follow the model-specific instructions supplied with the kit or in your dryer's installation manual
• Use rigid or semi-rigid metal ducting only; avoid plastic or vinyl
• After assembly, check for secure connections, no kinks, and unobstructed airflow

The main PCB assembly is an OEM part for LG dryers. This control board is responsible for managing and coordinating the various functions and cycles of the appliance.

A bad main control board assembly can occur due to electrical issues, component failure, or other internal malfunctions. If you notice symptoms such as the dryer not starting, unresponsive buttons or controls, or error codes appearing on the display, it may be time to replace the main control board assembly.

Symptoms of a bad main control board assembly include:

• Dryer not starting
• Unresponsive buttons or controls
• Error codes appearing on the display

Restore the function of your LG dryer by replacing the faulty main control board assembly with this genuine OEM part. This OEM LG part can also be used on Kenmore/Sears appliances. 

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.