Dwu8460aax Maytag Parts

Note: Check Serial Number for correct part

This float palnut is a push-on retainer that secures the dishwasher's water-level float to its stem. Keeping the float anchored helps the overfill protection work properly, supporting correct fill levels and helping prevent leaks from overfilling. What it does:

• Holds the float in position so it can move freely with water level changes
• Helps the float reliably actuate the overfill/float switch
• Replace if cracked, loose, or missing
• Typical symptoms include a loose or wobbly float, the float popping off, erratic filling, overfilling, or leaks near the float area

• One float palnut

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float assembly
• Remove the old retainer; press the new palnut squarely onto the float stem until snug
• The float moves freely up and down before reassembling

Attaches to the inner tub for the upper rack

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

This power cord strain relief secures the cord where it passes through the appliance cabinet, protecting the jacket and preventing pull on internal connections. Replacing a cracked or missing connector restores a safe, stable cord entry. What it does:

• Secures the power cord at the cabinet entry to relieve strain on internal terminals or junction connections
• Provides a protective bushing to reduce abrasion of the cord jacket against cabinet edges
• Helps maintain proper routing and support for the incoming power cord
• Typical signs it's needed: loose or wobbly cord at entry, broken/missing connector, or visible chafing on the cord jacket

• 1 strain relief connector

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove the access cover, release and remove the old strain relief, and route the cord through the new connector
• Seat the connector fully so it captures the cord's outer jacket—not the individual conductors
• After reassembly, verify the cord is secure and does not move at the entry point

To order indicator lens use WP22001948.

This impeller assembly replaces a worn or damaged wash-pump impeller to help restore water circulation and spray pressure for better cleaning. Commonly used in compatible Whirlpool wash pumps to address weak wash performance. What it does:

• Spins inside the wash pump to move water through spray arms; damaged fins reduce spray force and cleaning.
• Restores proper flow during wash cycles — symptoms of failure include weak or uneven cleaning.
• Reduces abnormal pump noise and motor strain when the impeller is intact; cracked or missing fins can cause humming or grinding.
• Works with the pump housing and seals to route water; a failed impeller can allow internal leakage or cavitation.

• Always disconnect power (and water, if applicable) before servicing the appliance.
• Inspect pump seals, gaskets, and surrounding components; replace any damaged parts to prevent leaks.

This O-ring seal fits into a groove to create a tight, leak-resistant barrier where two parts join. Replacing a worn O-ring helps stop drips at connections and keeps your appliance running reliably. What it does:

• Forms a compressible seal between mating parts (fittings, housings, or tubing)
• Helps prevent water or fluid leaks at joints
• Maintains proper pressure and flow within the sealed path
• Replace if you see seepage at the connection or the ring is cracked, flattened, brittle, or swollen

• 1 O-ring seal

• Disconnect power and shut off water supply before servicing
• Clean the groove and mating surfaces; remove debris that could compromise the seal
• Lightly lubricate with manufacturer-approved silicone grease; avoid petroleum-based products
• Seat the O-ring without twisting; reassemble carefully and check for leaks after testing

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

This replacement screw secures appliance panels, brackets, and components. Using the correct size restores a snug fit to reduce vibration, prevent loosening, and keep assemblies properly aligned during operation. What it does:

• Fastens sheet metal and component brackets in designated locations
• Replaces missing, stripped, or corroded hardware
• Helps eliminate rattling and vibration from loose panels
• Maintains proper alignment of covers and assemblies

• 1 screw

• Disconnect electrical power; shut off water or gas supplies if applicable
• Match length/thread to the original; replace one fastener at a time to preserve alignment
• Start by hand to avoid cross-threading; use the correct driver size
• Snug firmly but do not overtighten to prevent stripping

Specs: No.8X1/2 HEX WASHER HEAD

A small trim screw designed to secure appliance trim pieces and molding, restoring a finished look and keeping panels held firmly in place. Ideal when a trim piece is loose, missing a fastener, or shows minor rattling. What it does:

• Fastens trim, molding, or decorative panels to the appliance frame
• Restores secure mounting and helps eliminate loose or rattling trim
• Replaces missing or stripped fasteners that cause gaps or poor fit
• Compatible with common trim attachment points where OEM screw is specified

• Disconnect power or unplug the appliance before attempting repairs
• Use the correct screwdriver bit to match the screw head to avoid stripping
• Install by hand to start threads, then tighten snugly—do not overtighten
• Verify trim alignment after installation and test that the panel is secure

This tub wheel mounts on the dishwasher's tub wall to guide and support the rack as it slides in and out. Replacing a worn wheel restores smooth rack movement and helps prevent binding, noise, and derailments.

• Mounts to the tub to provide rolling support for the dish rack/rail
• Replaces cracked, flattened, or missing wheels that impede rack travel
• Helps fix racks that stick, bind, are hard to pull/push, or derail
• Reduces grinding or squeaking from the rack area

• Disconnect power at the breaker before servicing
• Open the door and pull the rack forward for access
• Release the old wheel from its retainer/axle per your model's design; install the new wheel in the same orientation
• Ensure the wheel spins freely and the rack slides smoothly before use

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.