Fex180cso Parts

This dryer thermostat monitors internal air temperature and opens/closes the heater circuit to keep drying safe and consistent. Replacing a weak or failed thermostat restores proper heat and helps prevent overheating or nuisance shutdowns. What it does:

• Senses exhaust/heater housing temperature and switches the heating circuit based on temperature
• Helps maintain target drying temperatures for consistent performance
• Provides over-temperature protection by opening the circuit if heat rises too high
• Common symptoms include no heat or weak heat, long dry times, heat cutting out mid-cycle, or the dryer running hotter than normal

• 1 thermostat

• Disconnect power before servicing; heating components can be live and hot
• Access location varies by model; typically mounted on the heater or blower housing behind a rear or front panel
• Transfer wires from the old thermostat to the new one one-at-a-time and secure firmly; ensure the mounting surface is clean and flat
• After replacement, check and clear the venting/duct for proper airflow to prevent repeat failures

This dryer timer controls and advances the cycle you select, routing power to the correct components and shutting the dryer off at the proper time. Replacing a worn timer restores consistent cycle timing and end-of-cycle shutoff.

• Controls cycle selection and duration
• Advances the dial through the program and turns the dryer off at the end
• Routes power to dryer components at the correct times during the cycle
• Signs of a failing timer may include: cycle not advancing, running indefinitely, stopping early, or erratic timing

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the control knob and access the console to unmount the old timer
• Label or photograph wiring; move terminals to the new timer one at a time to avoid miswiring
• Align the timer shaft with the dial, secure the timer, and test operation before reassembly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This trunnion plate secures the washer's inner basket to the drive hub/trunnion, keeping the tub centered and stable during spin. Replace it if the basket feels loose, wobbles, or makes scraping/knocking noises from the hub area. What it does:

• Couples the inner basket to the trunnion/drive hub so the basket spins true
• Helps maintain alignment to reduce vibration and tub-to-basket contact
• Wear can allow play or slippage at the hub connection
• Common symptoms: wobble, scraping/grinding, excessive vibration, poor spin results

• One trunnion plate

• Disconnect power and wear cut-resistant gloves before servicing
• Access typically requires removing the agitator/wash plate and lifting out the inner basket
• Clean and inspect mating surfaces; align the plate correctly and tighten fasteners evenly
• Check related parts for wear and replace if needed

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

This water inlet valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper filling and helps prevent unwanted water entering the unit between cycles.

• Opens and closes to regulate water flow when energized by the control
• Failure can cause no fill or very slow fill during cycles
• Can contribute to leaks at the back or water-inlet/fill error alerts

• Disconnect power and shut off the water supply before servicing
• Keep a towel or pan handy to catch residual water; relieve hose pressure
• Note/label hose and wire locations; transfer any brackets or screws from the original valve as needed
• Restore water and power, tighten connections, and check carefully for leaks with a test fill

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This temperature control thermostat regulates your appliance's internal temperature by opening and closing the electrical circuit as conditions change, helping it reach and maintain the setting you select for consistent performance. What it does:

• Senses temperature and opens/closes contacts to control the system
• Helps maintain the set temperature by cycling the unit on and off
• Can lead to inconsistent temperature or a control knob that has no effect

• 1 temperature control thermostat

• Disconnect power before servicing; use proper PPE around sharp sheet metal
• Photograph wiring and transfer conductors one at a time to the new control
• Route it exactly as original and avoid kinks or sharp bends
• Set the control to mid-range after installation and allow the unit to stabilize before fine-tuning