Ffbd2406ns1a Parts

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

The Rail End Cap is an OEM part for Frigidaire dishwashers. This small but essential component is designed to fit at the end of the dishwasher rack rails, preventing the racks from sliding off the rails when pulled out for loading or unloading. The end caps also help to protect the dishwasher’s interior walls from scratches or damage that might occur if the metal racks were to come into direct contact with them. 

Symptoms of a failing rail end cap include:

• Dishwasher racks sliding off the rails
• Difficulty pulling racks in and out smoothly
• Noticeable damage or scratches inside the dishwasher

Causes of rail end cap damage typically involve physical stress from frequent use, accidental breakage during loading, or degradation of the material over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Upper Dishrack Wheel is an OEM part for Frigidaire dishwashers. This part attaches to the upper dishrack, allowing it to slide in and out smoothly along the dishwasher's tracks for easy loading and unloading of dishes.

Common causes of a bad dishrack wheel include wear and tear from frequent use, damage from heavy loads or improper handling, and breakage due to impact.

Symptoms of a bad Upper Dishrack Wheel include:

• Difficulty sliding the upper dishrack in and out
• The upper dishrack derailing or not staying on its tracks
• Unusual noises when moving the dishrack
• Visible damage or wear on the wheel

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Latch Assembly is an OEM part for Frigidaire dishwashers. It is designed to securely fasten and anchor the dishwasher door during active cycles.

Causes relate to typical stresses from normal opening and closing motions. Regular cleaning chemicals like rinse aid may also degrade latch parts faster.

Symptoms of a faulty latch assembly can include:

• The inner door popping open unexpectedly during washing or drying
• Difficulty fully closing or sealing the door shut
• Improper adhesion or alignment of door gaskets and seals
• Damage or wear to connecting latch components over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Heating Element Nut is an OEM part for Frigidaire dishwashers. It plays a crucial role in securing the heating element in place, ensuring it functions effectively to heat water during the wash cycle. This component ensures the stability and proper operation of the dishwasher's heating element, contributing to the machine's overall efficiency and performance.

Causes of a bad part can include physical damage during maintenance or installation, corrosion over time due to exposure to water and detergents, or general wear and tear that affects its ability to securely hold the heating element in place.

Symptoms of a bad Heating Element Nut include:

• Loose heating element, leading to inefficient heating or water not heating at all
• Water leakage from the heating element area, potentially caused by a poor seal
• Unusual noises during the dishwasher cycle

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dishwasher Door Spring is an OEM part for Frigidaire dishwashers. It helps to balance and support the weight of the dishwasher door, allowing it to open and close smoothly and safely. The spring ensures that the door remains stable at any angle, preventing it from dropping too quickly or not staying open. This spring, 8" in length, is sold individually. 

The door spring may need to be replaced if it becomes worn out, stretched, or broken. Causes of a bad door spring can include frequent use, excessive force when opening or closing the door, and general wear and tear over time.

Symptoms of a bad dishwasher door spring include:

• The door dropping open quickly
• Difficulty in keeping the door open at various angles
• The door not closing properly
• Unusual noises when opening or closing the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Latch Assembly is an OEM part for Frigidaire dishwashers. This part ensures the dishwasher door closes securely and stays locked during the washing cycle. This component is crucial for the dishwasher's safety and efficiency, as it prevents water from leaking during operation and ensures the cycle continues without interruption.

Causes of a bad Latch Assembly can range from wear and tear over time, leading to a weakened or broken latch mechanism, to accumulation of debris or damage from an impact, preventing the latch from engaging correctly.

Symptoms of a malfunctioning Latch Assembly include:

• The dishwasher door not closing or latching properly, which may prevent the machine from starting.
• Leakage around the door due to an incomplete seal.
• The dishwasher stopping mid-cycle if the door unlatches, posing a risk of water spillage and inefficiency.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This flapper valve is the dishwasher's one-way drain check. It directs wastewater out and helps prevent backflow into the tub, promoting complete draining and reducing standing water, odors, and water returning after the drain cycle.

• Maintains one-way water flow from the sump/pump to the drain hose
• Helps prevent backflow from the sink or air gap into the dishwasher tub
• Wear, warping, or sticking can lead to slow draining or water left in the tub
• May also present as water backing into the tub after a cycle or intermittent drain faults

• Disconnect power and turn off water supply before servicing
• Access the valve at the drain outlet/pump area; note hose and clamp orientation
• Match the original valve orientation; the flapper should open toward the drain hose (direction of flow)
• After reassembly, run a short fill-and-drain test and inspect for leaks and proper draining

The Door Hinge Kit is an OEM replacement part for Frigidaire dishwashers. Located on the left and right side of the dishwasher doorway, the hinges are responsible for supporting the weight of the dishwasher door and facilitating smooth opening and closing. The kit is composed of two brackets and all of the extra hardware needed to install it on a dryer.

Causes of failure include wear and tear of hinge parts over many door openings and closings, damage due to overload or misuse, and deterioration of hinge components exposed to moisture.

Symptoms include:

• Loose or sagging dishwasher door
• Difficulty opening or closing the door
• The door does not stay securely closed during cycles
• Noises or squeaks emanating from hinge areas

This OEM replacement is also compatible with Electrolux, Kelvinator, and some Kenmore models.

The Delivery Tube is an OEM replacement part for Frigidaire dishwashers. This tube is designed to supply water to the upper spray arm from the pump assembly. By doing so, it plays a role in ensuring that the upper rack of dishes receives adequate water coverage for effective cleaning. 

Causes for a malfunctioning Delivery Tube can include blockages from food particles or mineral deposits, general wear and tear from regular use, or damage incurred during maintenance or installation.

Symptoms of a bad Delivery Tube include:

• Inadequate cleaning of dishes on the upper rack
• Water not reaching the upper spray arm
• Unusual sounds during the wash cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Level Float Switch Assembly is an OEM replacement part for Frigidaire dishwashers. It uses a floating switch design to accurately sense water levels filling and draining during cycles. Proper level detection allows for optimized wash and rinse action and water volume control.

Causes of a bad float switch assembly can include wear and tear over many years of use, interfering with free float movement. Mineral or scale deposits may accumulate on float components, inhibiting functionality. Physical damage from impact could introduce leaks.

Symptoms of a bad float switch assembly include issues such as:

• Inability to properly detect water levels
• Long fill or drain times
• Failure to fill or drain completely
• Potential overflow or standing water issues
• Error codes pointing to level sensor faults

This OEM Frigidaire replacement part is also compatible with some Electrolux, Westinghouse, and Kenmore dishwashers.

The Silverware Basket is an OEM replacement part for Frigidaire dishwashers. It holds and protects silverware during the dishwashing cycle. The basket is designed to fit seamlessly within the dishwasher, providing a convenient and accessible storage solution for silverware.

Causes of a bad silverware basket can include wear and tear over time, damage to the basket or its components due to mishandling or impact or exposure to harsh detergents or chemicals

Symptoms of a bad silverware basket:

• Rust or corrosion
• Difficulty loading or unloading silverware
• Silverware falling out of the basket during the wash cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Dishrack Roller Assembly is an OEM component specifically designed for Frigidaire dishwashers. It consists of precision ball bearing rollers that allow smooth extension and retraction of the lower dishrack.

Symptoms of a bad roller assembly include:

• The lower rack getting stuck and not fully extending or retracting 
• Scratching or grinding noises coming from the roller area
• Difficulty accessing the lower rack due to poor movement

Causes can be general wear and tear over time, an incident that damaged the rollers, or a malfunction of the guiding mechanisms.

This OEM Frigidaire replacement part is also compatible with some Electrolux, Gibson, and Kenmore models.

The Kickplate Assembly is an OEM replacement part for Frigidaire dishwashers. It forms the bottom protective barrier that prevents damage from kick impacts during loading and unloading.

Causes of a bad kickplate can include cracks or fractures from repeated contact, broken mounting clips, or detachment from normal wear over time.  

Symptoms of a bad kickplate assembly include:

• Compromised protection of internal tub components  
• Exposed wires or mounting hardware pose a safety hazard
• Mounting clips or hinges that become detached

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Lower Spray Arm Support is an OEM part for Frigidaire dishwashers. This support provides a secure attachment point for the lower spray arm, ensuring it rotates freely and distributes water evenly throughout the dishwasher for effective cleaning. It helps maintain the stability and proper function of the lower spray arm.

Common causes of a bad lower spray arm support include wear and tear, physical damage from loading or unloading dishes, and blockages that impede the spray arm's movement.

Symptoms of a bad lower spray arm support include:

• The lower spray arm not rotating properly
• Poor cleaning performance on the lower rack
• Unusual noises during the wash cycle
• The lower spray arm falling off or becoming loose

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Inlet Tubing is an OEM part for Frigidaire dishwashers. This tubing allows water to flow from the home's water supply lines into the dishwasher. Properly functioning inlet tubing is essential for supplying water to fill cycles and operate through different wash and rinse cycles.

Causes of a bad water inlet tubing can include mineral or sediment build up inside the tubing restricting water flow, splitting or cracking of the tubing material from stress or age, or damage from sharp objects or wear and tear.

Symptoms of a bad water inlet tubing include:

• The dishwasher failing to fill properly or slowly filling.
• Fluctuations in water pressure during cycles.
• Excessively long fill times.
• None or intermittent water flow into the dishwasher.
• Leaks or water drips around the supply lines.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.