Fftr181114qw4a Parts

This defrost pan collects water from the refrigerator's automatic defrost cycle and sits over warm components so it can evaporate safely. Replace a cracked or deformed pan to help prevent floor puddles and musty odors. What it does:

• Collects defrost condensate and allows it to evaporate in the machine compartment
• Helps keep floors dry by managing defrost water
• Replace if the pan is cracked, warped, leaking, or missing
• Common symptoms include water under the refrigerator, recurring puddles, or musty odors

• 1 defrost drain pan

• Disconnect power and pull the refrigerator away from the wall before servicing
• Remove the rear access panel to reach the drain pan
• Slide out the old pan carefully and empty any water; reuse any original supports/brackets if present
• Set the new pan on its supports, ensure the drain outlet/tube drips into the pan, reinstall the panel, restore power, and check for leaks

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

The Door Hinge is an OEM part for Frigidaire refrigerators. It is a component that allows the refrigerator door to swing open and closed easily while ensuring a proper seal is maintained each time. The hinge supports the weight of the door and controls its movement into both open and closed positions.

Causes of a bad hinge can include continued normal wear and tear over time, damage from excessive weight or impact, or corrosion that causes mechanisms to freeze up or fail.

Symptoms of a bad hinge include:

• The door not sealing properly when closed
• Difficulty in opening or closing the door
• The door swinging open or closed unintended
• Noise or squeaking coming from the hinge area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

This condenser fan motor drives the fan that cools the condenser coils and compressor. Replacing a weak or noisy motor restores proper heat removal so the refrigerator can reach and maintain set temperatures.

• Rotates the condenser fan to move air across the condenser coils and compressor
• Helps prevent compressor overheating and supports stable cooling performance
• Common symptoms of failure: fan not running, loud noise from the rear bottom, warm refrigerator temperatures, or hot cabinet sides

• Disconnect power and pull the refrigerator away from the wall; remove the lower rear access panel
• Note wire positions; disconnect the harness and remove the old motor
• If reusing existing parts, carefully transfer the fan blade and any mounting hardware; mount the new motor securely
• Ensure the blade spins freely with proper clearance; reinstall the cover and restore power to confirm the fan runs with the compressor

The Refrigerator Hook-Auto Closer is an OEM part for Frigidaire French door refrigerators. Located on the top inside edges of the refrigerator doors, the hook-auto closer attaches the closing mechanism arms to allow automatic opening and closing functions. 

Symptoms of a bad hook-auto closer include: 

• Doors detached from closing mechanism  
• Linkages slipping out of place 
• Loose or unstable door movement
• Grinding noises when doors open or close

Causes of a bad hook-auto closer can be damage or deformation from excessive impact, broken weld points, or normal wear over time.

This genuine Frigidaire part is compatible with some Electrolux and Kenmore French door refrigerator models as well.

This black center hinge bracket mounts to the cabinet at the middle door position to support and align the refrigerator door. Replacing a bent or worn bracket restores smooth door swing and a dependable gasket seal.

• Mounts the center hinge assembly to the cabinet for stable door support
• Provides the pivot point for the door via the hinge pin/cam hardware
• Helps keep the door aligned so the gasket seals properly
• Common symptoms: sagging or rubbing door, door not closing/sealing, popping open, or hinge-area squeaks/scrapes

• Disconnect power and support the door; remove items from the door to reduce weight
• Remove center hinge cover and screws; lift door off the hinge
• Transfer reusable hardware to the new bracket
• Reinstall bracket and door, then check door alignment and gasket seal

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

Color: White

This PTC compressor start relay briefly powers the compressor's start winding to get the motor turning, then drops out as it warms. Replacing a weak relay can restore consistent compressor starts and stabilize refrigerator and freezer temperatures.

• Momentarily energizes the compressor's start winding; disengages automatically as the PTC element heats
• Helps protect the compressor by removing the start winding after startup
• Symptoms of failure can include compressor clicking but not running
• Intermittent cooling or warming temperatures between cycles
• Heat discoloration or a burnt odor around the start device

• Disconnect power and remove the rear lower access panel
• Note wire locations; remove the start device cover/retainer and pull the old relay straight off the compressor pins
• Inspect compressor pins; firmly seat the new relay and reconnect wiring
• Reinstall covers/panels, restore power, and verify normal compressor start

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

Color: White

This compressor start relay (PTC) briefly powers the compressor's start winding to ensure reliable start-up. Replacing a failed relay can stop repeated clicking and help a non-starting compressor restore normal refrigerator cooling.

• Provides a timed, resistance-based boost to the compressor's start winding, then drops out of the circuit
• Common symptoms: compressor hums then clicks off, frequent clicking from the rear, warm fridge/freezer, intermittent cooling
• Mounts directly on the compressor terminals; works with the separate overload protector and, if equipped, a run capacitor
• Visible signs of failure may include heat damage, burnt odor, or loose/rattling pieces inside the old relay

• Unplug the refrigerator and remove the lower rear access panel to reach the compressor
• Note wire routing and orientation; transfer any harness/retainer and seat the relay fully on the compressor pins
• If a run capacitor is present, discharge it before handling and reconnect to the same terminals
• Inspect the overload and connectors; replace any heat-damaged components

This door shelf bin restores usable storage on the inner door. Replace a cracked, broken, or missing bin to keep items organized and help prevent spills when opening and closing the door.

• Attaches to the door liner to hold food items and containers
• Replace if the original is cracked, warped, or has broken mounting tabs
• Common symptoms: bin falls off or won't stay seated, reduced door storage, items tipping or sliding
• Restores proper fit and organization on the door

• Empty the bin and support the door while working
• Remove the old bin by lifting up and out; align the new bin with the door rails and press down until fully seated
• Do not force; ensure you're installing in the correct door position for this bin
• No electrical work required; handle plastic parts carefully to avoid cracking

This condenser fan motor powers the refrigerator condenser fan to move air across the condenser coils, helping the appliance cool efficiently. Replaces a failed motor to restore proper condenser airflow and reduce overheating risk. What it does:

• Turns the condenser fan blade to circulate air over condenser coils
• Helps maintain correct operating temperature for the compressor and refrigerant
• Commonly used when the fan is noisy, not spinning, or the compressor overheats
• Works as the main motor for the condenser fan assembly in the cooling system

• Disconnect power to the appliance before starting any repair
• Handle the fan blade and motor mounting carefully to avoid bending blades or damaging wiring
• Test operation after installation;