Fghd4261kw1 Parts

This seal kit restores a tight, insulated barrier around a window air conditioner. Replacing worn or missing seals helps block gaps and drafts, reduce noise and vibration, and maintain efficient cooling performance.

• Creates an air-tight barrier between the unit, sash, and window frame
• Helps reduce warm air infiltration, dust, and insects entering around the A/C
• Supports proper cooling by minimizing recirculation of hot outdoor air
• Helps resolve drafts, reduced cooling, condensation at the cabinet, or rattling noises

• Unplug the unit before servicing; work on a cool appliance
• Remove old foam and adhesive; clean and dry surfaces before applying new seals
• Measure and cut seals to length; avoid stretching or compressing the foam during install
• Press firmly to ensure full contact; follow your model's installation guide for placement

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

The Fill Tube Kit is an OEM part for Frigidaire refrigerators. It contains the tubes used to direct water from the water supply line into the refrigerator's water dispenser and ice maker. As these tubes can degrade over time due to mineral buildup or cracking, this kit provides a like-new replacement to ensure optimal water flow.

Causes of a bad fill tube include mineral or limescale deposits restricting water flow, cracks or leaks developing from general wear and tear, or accidental damage from installation or maintenance issues.

Symptoms of a bad fill tube are:

• Slow or inconsistent water flow from the dispenser
• Dripping or leaks from the fill tube connection points
• Ice maker not working or producing small or misshapen ice cubes
• Water backing up or overflowing in the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door handle bar lets you grip and open the appliance door smoothly. It restores a secure, comfortable handle when the original bar is loose, worn, or damaged, helping the door operate as intended.

• Provides a sturdy handhold to open and close the door
• Replaces a loose, cracked, or missing handle bar
• Helps ensure proper door operation and user safety
• Cosmetic refresh for a worn or scuffed handle area

• Unplug the appliance before servicing
• Use the correct screwdriver/hex driver per your model's fasteners
• Support the door while loosening and tightening handle screws
• Do not overtighten; align and snug evenly to avoid damage

The Control Assembly is an OEM part for Frigidaire refrigerators. It includes the electronic circuit boards, touch pad controls and wiring that allow for operation and monitoring of refrigerator functions and temperatures.

Causes can be short circuits, water damage, power surges over time that degrade electronic components. 

Symptoms of a bad control assembly include:

• Failure of temperature or setting displays
• Inoperable or unresponsive touch controls
• Refrigerator malfunctions like freezing up or not cooling
• Repeated blowing of fuses

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

A direct-replacement freezer basket handle that restores a secure grip for lifting and removing the freezer basket. Simple swap that helps make basket removal easier and reduces digging or awkward handling. What it does

• Provides a secure grip point for removing, carrying, and repositioning the freezer basket.
• Replaces a cracked, broken, or missing handle to restore normal basket operation.
• Helps prevent slippage or dropping of the basket when loading or unloading.
• Matches original fit and attachment style for straightforward replacement on compatible units.

• One freezer basket handle.

• Disconnect power and remove stored items from the basket before servicing.
• Most installs require removing the basket to access the handle; basic hand tools may be needed.
• Follow model-specific instructions in the service manual for removal and fastening details.

This spray arm assembly distributes high-pressure wash water inside the dishwasher and spins to cover the racks. Replacing a cracked or clogged arm restores proper spray coverage for cleaner dishes and consistent wash performance. What it does:

• Rotates as water flows to spray dishes evenly across the tub
• Channels water from the circulation pump through precision jets
• Helps resolve poor cleaning results or spots left on dishes
• Addresses issues like a spray arm that won't spin, clogged nozzles, or visible damage

• 1 spray arm assembly

• Disconnect power at the breaker and turn off the water supply before servicing
• Remove the rack if needed to access the arm
• Release the locking tabs or unthread the retaining cap to remove the old arm
• Seat the new arm fully, secure the retainer, and confirm it spins freely before a test cycle

The Drain Pump is an OEM part for Frigidaire dishwashers. It is responsible for removing water from the dishwasher tub at the end of each cycle. The drain pump works in conjunction with the drain hose to efficiently expel dirty water and ensure dishes are thoroughly dried.

Symptoms of a bad drain pump include:

• Water not fully draining out of the bottom of the dishwasher tub
• Puddles or standing water left inside after a cycle is finished
• Mildewy or musty smells emitting from the appliance
• Loud or grinding noises coming from the drain pump motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

The Slide Assembly is an OEM part specifically designed for Frigidaire refrigerators. It secures crisper and pantry bins within the refrigerator interior, providing gliding functionality for easy access to stored items. 

Causes of a bad slide assembly include loose or broken mounting features, damaged rollers, or bent metal rails failing to guide bins smoothly.

Symptoms of a bad slide assembly can include:

• Difficulty removing or replacing crisper/pantry bins
• Bins failing to close fully or stay securely in place  
• Loud squeaking or grinding noises developing
• Dislodged mounting screws or loose mounting points

Replacing with this OEM slide assembly restores smooth operation. It is purpose-built to support everyday use without degradation. 

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before further component wear develops.
 

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

Replacement water tube that routes water from the inlet valve to the refrigerator dispenser and ice maker, helping restore proper water flow for reliable dispensing and ice production. What it does:

• Carries water from the refrigerator inlet/valve to the dispenser and ice maker fill system.
• Used when cracked, kinked, clogged or brittle tubing prevents water flow.
• Helps stop leaks and restore normal ice maker fill when tubing is damaged.
• Addresses symptoms such as no water at the dispenser, ice maker not filling, or visible leaking under the fridge.

• Turn off the water supply and unplug the refrigerator before beginning any work.
• May require basic hand tools and careful routing to avoid kinks; do not overtighten fittings.
• Inspect and replace any damaged clamps or seals; test for leaks after reconnecting the water supply.

The Handle Mounting Block is an OEM part for Frigidaire refrigerators. It is a component that secures the door handles in place and allows for proper opening and closing functionality. The handle mounting block is designed to provide a sturdy anchoring point for the handles while absorbing potential stresses.

Causes of a bad handle mounting block can include wear and tear over time, cracks or breaks due to overtightening of handles, or physical damage from impacts or mishandling.

Symptoms of a bad handle mounting block include:

• Loose or sagging door handles
• Difficulty opening or closing the refrigerator door
• Handles detaching from the door
• Cracks or breaks visible in the mounting block

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water inlet tube routes water from the inlet valve to the ice maker and dispenser, restoring proper water flow and helping prevent leaks. Use when the original tube is cracked, split, or blocking water delivery. What it does:

• Directs water from the refrigerator inlet valve to the ice maker and dispenser assembly.
• Restores normal water flow if the original tube is crushed, cracked, or blocked.
• Helps stop leaks associated with damaged or deteriorated inlet tubing.
• Common symptoms: no water to ice maker or dispenser, slow dispenser flow, or visible leaking beneath the fridge.

• Disconnect electrical power and shut off the household water supply before starting.
• Handle tubing carefully and avoid sharp bends or kinks when routing.
• Check and reuse or replace any associated fittings, clips, or seals as needed for a secure, leak-free connection.

This refrigerator drain tube channels defrost water from the evaporator to the rear drain pan so it can evaporate. Replace a cracked, missing, or clogged tube to stop interior leaks and ice buildup.

• Routes defrost meltwater from the freezer drain to the condenser drip pan
• Helps prevent pooling under crisper drawers or water on the floor
• Common failure symptoms: water under drawers, ice sheet in the freezer bottom, recurring drain clogs or freeze-ups, dripping at the rear base
• Restores proper drainage when the original tube is brittle, split, or obstructed

• Disconnect power; pull the unit forward and remove the lower rear access panel
• Remove the old tube from the drain outlet and drip pan; clear any ice/debris with warm water—avoid sharp tools
• Seat the new tube fully on the drain outlet and position the outlet into the pan; verify flow by pouring warm water down the drain
• Restore power and monitor for leaks as normal defrost cycles resume