Ge Gss22jfmdww Refrigerator Parts

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

Just enter the appliance model and the all the parts are pictured! Really easy! Read more

• Freezer too cold
• Fridge too cold
• Too warm
• Freezer section too warm

Yes, a 49-yr old woman fixed this fridge all by herself! AppliancePartsPros was very helpful in the diagnosis of the problem, which I determined to likely be the result of defrost failure. There was a large amount of ice and frost coating the back of the freezer despite the inside temp being 42 degrees. My husband thought I was crazy to think it was a problem with ice when the temperature was warm, but I told him to trust me and I would attempt the repair. He just wanted to throw the old one... Read more

• Freezer section too warm

New cond fan & new evap fan & new defrost heater unit Read more

Changed out the valve and cleaned the lines out Read more

After disconnecting power to the fridge, I first removed the ice maker/water dispenser/fridge control faceplate. This easily popped out using a flat head screw driver. Then disconnected the 3 wire harness connections to the control board. I next removed the plastic dispenser housing shield. There's only 4 screws that hold this on. Finally, I removed the Micro-switch, disconnected the two wire connectors and installed the replacement switch and reinstalled everything. The repair took only... Read more

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Ice maker dispenses too much ice

First - I am not a handyman so bear with me. Turned out not only the auger fins were broken off but also the ice dispenser crusher cover had cracks and breaks on it. First - AppliancePartsPros.com has awesome shipping. Because i didn't know right away the crusher cover was broken, I had to do two orders. Each order was received next day in afternoon. Video is great. Tells exactly how to do. There are two issues you will run into. Remembering the exact sequence of all the washers and... Read more

• Leaking
• Ice maker not making ice

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

• Fridge too warm

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

BEWARE THE HAIRDRYER In an effort to unfreeze the indoor water supply line with a hairdryer the extreme heat deformed not only the activator paddle but the housing that surrounds it. In the time it took to order and install replacement parts the frozen blockage had thawed. Back in business for now and if the problem reoccurs I will be looking for a different path to resolve the issue. Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

We bought a new house that has a 15 year old GE Monogram built in fridge. The home warranty people sent two guys out saying it was nearly impossible to repair the fridge and they both suggested buying a completely new freezer door for the fridge and of course the warranty company said it was preexisting and we weren't covered. Shocker. I have lighting in the freezer but not the fridge. I purchased a door switch and replaced the old one but that didn't do the trick. So i purchased a 2 amp fuse... Read more