Ge Gss25lg Parts

The Dispenser Lever is an OEM part for GE refrigerators. This lever activates the dispensing mechanism, allowing you to release water or ice from the refrigerator's dispenser.

Causes of a bad dispenser lever can include regular wear and tear, damage from excessive force or mishandling, and breakage due to frequent use. 

Symptoms of a bad dispenser lever include:

• The dispenser lever not returning to its original position
• Difficulty in activating the dispenser
• The lever feeling loose or unresponsive
• Water or ice not dispensing when the lever is pressed

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

For the same part in white, purchase WR02X13424.

This top pan cover sits above the refrigerator's crisper drawers, creating a flat shelf surface and supporting the bins below. Replacing a damaged cover restores usable space and helps the drawers slide, align, and close properly.

• Forms the shelf surface over the produce/crisper drawers
• Supports food items and the crisper bins beneath
• Helps drawers open/close smoothly and seat correctly
• Replaces cracked, warped, or broken covers that cause sagging or misalignment

• Disconnect power and clear items from the shelf area
• Remove the crisper drawers to access the cover
• Lift out the old cover; transfer any slides or trim from the original if needed
• Set the new cover in place and reinstall drawers; handle any glass carefully

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

This freezer shelf trim replaces a damaged or missing edge piece on the freezer shelf. It attaches to the shelf/frame to provide a finished lip that helps contain items and restores the shelf's original fit and appearance.

• Provides the finished edge on a freezer shelf to help keep items from sliding off
• Attaches to the shelf/frame for a secure, correct fit
• Replace when cracked, warped, loose, or missing
• Common symptoms include a broken or jagged shelf edge, trim that won't stay attached, or items slipping off the shelf

• Unplug the refrigerator and remove items from the affected shelf
• Remove the shelf if needed; release and remove the old trim
• Align the new trim with the shelf/frame and press until fully seated and secure
• Do not force parts together; inspect the shelf/frame for damage before reassembly

This slide-out freezer shelf restores a smooth, stable storage surface and easy access in the freezer compartment. Replace a cracked, hard-to-slide, or missing shelf to regain capacity, organization, and the spacing your freezer was designed for.

• Provides a level storage surface and slides forward for better visibility and reach
• Secures into the side supports/rails at the designated freezer position
• Helps maintain intended spacing and airflow between freezer sections
• Typical symptoms: cracked or broken shelf, damaged tabs, won't slide smoothly, sits unevenly, or missing shelf

• Remove items from the area and support the shelf with both hands when removing/placing
• Align with the side supports/rails and slide fully into place; verify correct front/back orientation
• Do not force; ensure it is seated in the correct slots before loading
• Handle edges carefully; wear cut-resistant gloves to prevent injury

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

Refrigerator primary ice and water dual coil water inlet valve. For the filter valve order WR57X10024. For the assembly including both the primary and filter valve having the short bracket order WR57X10026. For the assembly including both the primary and filter valve having the long bracket order WR57X10022.

This ice dispenser auger drive mounts on the dispenser motor shaft and engages the ice bucket auger. Replacing a worn or stripped drive restores the connection so your refrigerator can move ice smoothly to the chute.

• Couples the dispenser motor to the ice-bin auger to rotate and move ice toward the chute
• On models with crushers, also drives the crushing mechanism
• Worn or rounded splines can cause little or no ice dispensing even though the motor runs
• May produce clicking/grinding noises from the door during dispense
• Visible cracking or play at the coupling indicates replacement is needed

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin to access the dispenser motor shaft in the freezer door
• Note the orientation; remove the old drive and seat the new drive fully on the shaft, transferring any original hardware if present
• Reinstall the ice bin, restore power, and test ice dispense

The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.  

Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Difficulty in opening or closing the door
• Visible cracks or breaks in the handle
• The handle detaching from the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power