Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't agitate or spins but doesn't clean clothes? The agitator coupler connects the agitator to the drive shaft. Easy DIY repair with video guide.
Before buying a new ($1200) washer, I found the trouble shooting guide and decided to check if my problem was a simple fix or a complicated procedure... turns out it was the simple fix. Removing the agitator was the hardest part, it lifted straight up, but took some muscle and a belt for leverage. Then I had to remove one bolt, lift off the damaged part, and put the new part on with the one bolt. Done. Works perfectly. Read more
Washer won't spin or agitate? This lid switch assembly detects if the lid is closed. Moderate DIY repair—front panel removal required. Video available.
Replaced lid switch assembly Read more
Secures the inner tub to the outer tub in top-load washers. Replace if hub is cracked, broken, or rusted out to restore proper drum alignment and stability.
The machine stopped working with a bang. There were chunks of large metal at the bottom. The drive plate had rusted through. My first step was to put a rag in the tub drain hole and save the pump. Except for grinding/chiseling off a frozen-corroded-rusty solid mass. The repair was rather easy. A couple of channel lock wrenches and a hammer didn't budge it. A monkey wrench will just round it off. You need that 1 11/6" wrench. The spindle nut was really stuck on there for my 14+ yo washer. I... Read more
Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.
I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more
Washer won't fill, leaks after cycles, or has no hot water? The triple water valve controls fill, rinse, and dispenser flow. DIY fix in under 1 hour.
My husband fixed it, he took out the leaky valve and replaced it with the new valve, which we received in the mail from your company, which was only a short time after we ordered it. Thank you for being so prompt. Our washer is only a little over 2 years old and upon looking online, we found out this model has since been discontinued due to problems. The parts are no longer available from GE, so we were thrilled to find your company online which carried the part. It saved us a lot of money... Read more
Secures the timer dial to the shaft on top-load washers. Replace if the knob spins freely or won't engage properly. Confirm fit with your model.
I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more
Fix a washer that won't spin or agitate. This motor capacitor stores energy to start and run the motor. DIY repair takes about 10 minutes with video help.
Washer would run through the cycle, but not agitate. I had to wait for it to pump down the water level to check spin, which also was not working. The motor would buzz when it should run, but not rotate, hard to hear for spin because the pump was running. Found I could start it by hand very easily by giving the pulley a spin, so I figured start switch, but there didn't appear to be one. I found what looked like a start capacitor zip tied to the chassis midway up the front, so my second guess was... Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Washer won't spin or agitate? A faulty lid switch prevents operation when the lid isn't closed. DIY-friendly repair, typically takes 10-15 minutes.
An online search of the problem (would not agitate or spin) indicated a bad lid switch. Then with model number was able to find an online video on how to change it. Next I opened the washer, like in the video (very easy) and made sure that the lid switch looked like the one I ordered from AppliancePartsPros.com. Of course with the model number it was easy to find the right part. The part arrived in 2 days with no special shipping. What great service! Since, the washer was already open,... Read more
Supports the washer tub and absorbs vibration during cycles. Replace if corroded, worn, or broken to prevent drum sagging and banging during operation.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Fix a washer that won't advance through cycles or skips fill/agitate steps. This timer controls cycle sequencing. DIY repair in about 30 minutes.
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
Suspension rod and spring assembly supports the washer tub and reduces vibrations. Replace if cracked, worn, or broken to restore proper tub support.
I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy! Read more
Fix a washer that won't spin or agitates but doesn't spin properly. This mode shifter assembly switches between agitate and spin cycles. Advanced repair.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more