Gss25ufpe Parts

This freezer door gasket replaces the perimeter seal on the freezer door. It restores a tight closure that keeps cold air in and moisture out, helping maintain proper temperature and reduce frost and condensation around the door. What it does:

• Seals the gap between the freezer door and cabinet to contain cold air and block humid room air
• Replaces a cracked, torn, shrunken, or warped gasket that no longer seals properly
• Helps address frost or ice near the door opening, moisture on the gasket, rising freezer temps, or a door that won't stay fully closed
• Supports consistent cooling and reduces air leaks that can lead to longer run times

• One freezer door gasket

• Unplug the refrigerator before servicing
• Warm the new gasket with hot water or low heat to relax shipping folds; do not overheat
• Remove the old gasket and clean the sealing surfaces; seat the new gasket fully in the door channel, starting at the corners
• Close the door and check for uniform contact (paper/dollar-bill test); allow the gasket to conform over 24 hours

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

The Pan Cover Front Gasket is an OEM part for GE refrigerators. This gasket provides a seal for the front edge of the refrigerator's crisper or pantry drawer pan cover, preventing cold air from escaping and ensuring that the contents remain at the optimal temperature for freshness.

Common causes of a bad gasket include regular wear and tear, exposure to food spills, or accidental damage from frequent opening and closing of the drawer.  

Symptoms of a bad pan cover front gasket include:

• The drawer not sealing properly, leading to temperature fluctuations
• Visible cracks, tears, or warping of the gasket
• Increased condensation or frost buildup in the drawer area
• Food items spoiling faster than usual

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This lower light shield is the clear lens that covers the lower refrigerator lamp, diffusing brightness and protecting the bulb from contact. Replace a cracked, missing, or yellowed cover to restore even lighting and a clean, finished look.

• Diffuses the lower compartment light for softer, more even illumination
• Acts as a barrier to help prevent accidental contact with the bulb and splashes
• Replace if the cover is cracked, discolored, warped, missing, or won't stay secured
• Installs over the lower light using the appliance's existing tabs or screws

• Disconnect power to the refrigerator before servicing
• Allow the bulb to cool before handling the lens
• Release retaining tabs or remove screws carefully; avoid over-flexing the plastic
• When reinstalling, do not overtighten to prevent cracking the shield

The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.  

Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Difficulty in opening or closing the door
• Visible cracks or breaks in the handle
• The handle detaching from the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Color: white. Measures about 18 inches wide by 4 inches high by 8 inches deep.

Color: white. It measures about 15 inches wide by 1 inch deep.

This refrigerator dispenser funnel extension attaches at the front of the dispenser to better direct the stream into your cup. Replacing a cracked or missing extension reduces splashing and helps keep the dispenser area cleaner.

• Directs the dispenser stream to help prevent splashes and drips
• Extends the spout area for easier filling of glasses and bottles
• Restores fit and appearance when the original is cracked, warped, or missing
• Common symptoms: water splashing at the dispenser, loose/broken piece, water running down the door

• Unplug the refrigerator and shut off water before servicing the dispenser area
• Remove the old extension by releasing its retaining tabs, if present
• Align the new extension with the slots and press until it snaps securely into place
• Restore power/water and test the dispenser to verify proper flow and a secure fit

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

Size: 8-18 AB TSQ 5/8 SS

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

This is the glass insert for the refrigerator pan cover, creating the flat shelf above the drawers. Replacing cracked or missing glass restores a stable, easy-to-clean surface and helps contain spills from reaching the storage areas below.

• Forms the flat shelf that tops the pan cover assembly over crisper/deli drawers
• Provides a sturdy surface for storing food items
• Helps contain small spills so they don't drip into drawers below
• Replace if the glass is cracked, shattered, chipped, bowed, or missing

• Disconnect power and remove food from the affected shelf area
• Lift out the pan cover frame and slide out the old glass
• Clean the frame's channels; seat the new glass fully and evenly
• Handle glass carefully and wear cut-resistant gloves