Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a noisy or non-working convection fan with this motor assembly. Restores even heating and airflow in your oven. Takes about 30 minutes to install.
Very easy fix. Turned of power at breaker. Removed oven door by lowering two "keepers" on the hinges for the oven door and sliding the door out of the oven. Removed the trim plate at bottom of oven by pushing it up.. Removed 2 screws that mount to the frame of the cabinet at the bottom that the trim plate hangs from. Then removed 4 screws that hold the oven into the cabinet at either side of the oven. Put two 5 gallon buckets in front of the oven and slid the oven out onto the side-by-side... Read more
10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.
All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more
Mounting nut secures the convection fan blade to the motor spindle. Replace if lost, stripped, or damaged during fan service or repair work.
I took the cover off and the fan had separated from the bushing. Ordered a new fan and nut and it took all of 5 minutes to replace. Probably saved $159.99 service call repair and that is with a coupon. Any one can do this repair, just make sure the oven is cold as you will come in contact with metal parts. Read more
Hex head mounting screw for ranges and ovens. Secures elements, panels, and internal components. Replace if stripped, missing, or damaged during repairs.
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Fix F9 error codes and oven shutting off during baking. This control cooling fan motor keeps electronics cool and prevents overheating. 15-minute repair.
The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more
Hex washer head screw secures oven panels, brackets, and door handles. Replace missing, stripped, or damaged screws to eliminate looseness and rattling.
It was very easy!. Just removed the screws off the trim plate and access was right there. The double oven was given to me but the handles were missing and the end caps so I just had to replace them. Read more
Oven won't heat or fan won't run? This high-amp SPDT switch routes power to locks, relays, and fans. Fixes intermittent operation. Moderate DIY fix.
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more
Microwave not heating but runs? Replace the magnetron to restore cooking power. Intermediate DIY repair taking 1-2 hours with proper safety steps.
I ordered the capacitor, diode, and magnetron in hopes that I would be able to complete the repair using the less expensive parts. I first removed the oven from the wall and then I removed the metal housing to access the internal parts. I discharged the capacitor using a pair of insulated needle nose pliers. Then I changed out the diode and the capacitor and reassembled the unit and tested it. It still did not heat so I disassembled the unit again and replaced the magnetron this time.... Read more
Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.
We replaced the broken door hinge. Read more
Microwave not heating? A failed high-voltage capacitor prevents the magnetron from working. Requires discharging and wall unit removal to replace.
Black hex washer screw for securing range components like door trim, control panels, and internal brackets. Replace missing or stripped screws during repairs.
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Replacement mounting screw for appliances. Secures components and reduces vibration. Needed when original screws are missing, stripped, or damaged.
I was very pleased to get the glass on time and it was a perfect match. The only thing I had trouble was to get the screws required to fix. The screws were not available, so spend too much time trying find equivalent screws in homedepot. Read more
Door pad gasket creates a seal between your oven door and front panel. Replace if worn, cracked, or causing heat loss. Confirm fit with your model number.
Ordered replacement from appliancepartspro.com and installed. Took maybe 10 minutes to remove old one and instal new. Read more
Fix a microwave turntable that won't rotate, stalls, or makes grinding noises. This motor spins the glass tray for even heating. DIY repair in 10 minutes.
Replace motor, 10 minute fix. No problems! Read more
Oven convection fan not working or making noise? This shaft-mount fan blade restores proper airflow and cooling. Easy DIY repair in under an hour.
Ordered fan assembly. Not difficult to install at all. Remove the back cover, remove the fan cover inside the oven, remove the motor/fan assembly and put it all together. Easy. Read more
Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.
A new electrode and the great schismatics on your website. The only thing that took some time was removing the 2 screws in burner pan. Once removed it was very easy to fix. Read more