Kg25h3xsl 475W Parts

This screw secures appliance panels, brackets, and trim so everything stays aligned and rattle-free. Replace missing, stripped, or rusted hardware to restore a solid fit and dependable operation. What it does:

• Fastens components to the cabinet/frame to maintain proper alignment
• Helps prevent vibration, rattling, and small gaps from loose hardware
• Replaces lost, damaged, or corroded screws to restore secure mounting
• Common signs include loose panels/trim, vibration noises, or shifting parts

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the part being fastened to keep holes aligned and avoid damage
• Start threads by hand to prevent cross-threading; realign if resistance is high
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

This retaining ring snaps into a groove to keep a component securely positioned on its shaft. Replacing a bent or missing ring restores proper fit and helps stop looseness, shifting, and noise from parts moving out of place.

• Locks into a machined groove to secure gears, shafts, or linkages
• Prevents axial movement that can cause wobble or separation
• Helps eliminate rattling, scraping, or intermittent operation from loose assemblies
• Direct replacement for a worn, stretched, or missing ring identified during service

• Disconnect power and allow all moving parts to stop before servicing
• Wear eye protection; retaining rings can spring free under tension
• Use proper snap-ring/retaining-ring pliers and avoid over-expanding the ring
• Ensure the ring is fully seated in the groove with correct orientation and retention

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This rubber foot replaces a worn or missing foot on the base of a stand mixer. It helps stabilize the mixer, reduce vibration and movement, and protect your countertop so the mixer stays steady during use. What it does:

• Provides non-slip grip to help prevent the mixer from sliding
• Cushions and helps reduce vibration
• Helps keep the mixer level for consistent operation
• Common symptoms include wobbling/rocking, "walking" on the counter, and scuff marks on the surface

• 1 rubber foot

• Unplug the mixer and remove the bowl/attachments before beginning
• Lay the mixer on a padded surface to access the base
• Pull the damaged foot straight out; clean the recess if needed
• Press the new foot fully into the hole until seated flush; replace additional feet as needed to keep the mixer level

This small retainer clip secures the drip bowl and coil surface element so they stay properly seated on the cooktop. Replacing a worn or missing clip restores a tight, level fit and reduces wobble during use. What it does:

• Holds the drip bowl to its mounting point and helps keep the surface element seated
• Maintains alignment to reduce movement and rattling
• Helps prevent the element from tilting so cookware sits more evenly
• Common symptoms: loose or wobbly burner/bowl, bowl won't stay seated, or a cracked/missing clip

• Retainer clip only

• Disconnect power at the breaker before servicing
• Lift out the coil element and drip bowl; note clip orientation for reassembly
• Snap the new clip into place carefully—avoid over-flexing the part
• Reinstall the bowl and element and ensure the burner locks in and sits level

This small retaining pin secures the bowl retainer/clip so the mixing bowl locks firmly in place during operation. Replace it if the original pin is missing or bent, or if the bowl won't stay seated. What it does:

• Anchors the bowl retainer/clip to the frame
• Keeps the bowl locked and stable during use
• Helps reduce bowl wobble, vibration, and rattling
• Common symptoms: bowl won't latch, rocks loose, or visible pin damage/missing

• 1 retaining pin

• Disconnect power before servicing
• Remove the bowl and access the bowl retainer/clip
• Support the casting; drive the old pin out with a small punch—avoid prying against the housing
• Align holes and install the new pin flush; verify the bowl latches securely and adjust the retainer per your model's service guide

This factory mounting screw secures components in place inside compatible appliances, helping maintain proper alignment and reliable operation.

• Fastens panels, brackets, or internal parts to prevent shifting and vibration
• Common fix when a panel or bracket is loose or rattling
• Resolve issues like gaps, misalignment, or buzzing from loose hardware

• Unplug power and shut off utilities before servicing
• Retain and reuse original hardware and clips where applicable
• Start threads by hand to avoid cross-threading, then tighten snugly without over-torquing

Replacement cam that restores proper engagement of the appliance's mechanical linkage so cycles run smoothly. Installs where the drive/shift mechanism needs a correctly timed cam to stop slipping or misalignment. What it does:

• Transfers rotary motion to the linked component so parts engage at the correct time
• Restores reliable engagement to reduce skipping, grinding, or irregular cycle behavior
• Commonly replaced if cracked, worn, or otherwise fails to engage properly
• Matches the OEM part name and fit as a direct replacement when the original cam is damaged

• Always disconnect power (and water, if applicable) before starting service
• Remove required access panels and note the original cam orientation for correct reassembly
• Inspect mating parts (shaft, clips, splines) and replace any damaged hardware before installing the new cam
• Reassemble panels and run a test cycle to ensure normal operation and correct engagement

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

This planetary is the replacement internal gear assembly that helps transfer motor motion to the agitator/impeller for proper wash action. It restores drivetrain engagement so the washer can agitate and spin more effectively. What it does:

• Replaces a worn or damaged planetary gear assembly that causes weak or no agitation/spinning
• Transmits motor torque to the transmission and agitator/impeller for normal wash cycles
• Can address symptoms like intermittent agitation, loud grinding noises, or slipping during cycles
• Fits into the transmission/gearcase as a direct replacement when the original planetary fails

• Inspect surrounding seals and gears during replacement
• Disconnect power and water supply before beginning any repair
• Use proper tools and follow OEM diagram for correct orientation and torque; avoid forcing parts to prevent damage
• Replace any worn fasteners or gaskets found during installation

Cap Hub covers and protects the appliance's hub, restoring a finished appearance and helping keep debris away from internal components. Use when the original hub cap is cracked, missing or visibly worn. What it does:

• Covers and conceals the drive/tub hub for a finished look.
• Helps keep lint and debris away from the hub area.
• Replaces cracked, broken or missing hub caps that expose the hub.
• Check the model-specific diagram for exact fit and orientation.

• Disconnect power (and water if applicable) before beginning any service.
• Part typically snaps or presses into place; the appliance's exploded diagram for the correct removal/replacement procedure.
• Do not force the part; inspect surrounding components and replace any damaged mounting hardware as needed.

The Transmission Housing is an OEM part for Whirlpool mixers. This component encases the transmission, which is responsible for transferring power from the motor to the mixing attachments. The housing ensures the transmission is protected from external damage and maintains the alignment and stability of internal components.

Over time, the transmission housing can become compromised due to regular use, exposure to food and moisture, or accidental impacts. Damage to this part can lead to misalignment, which affects the performance of the mixer.

Symptoms of a bad transmission housing include:

• Unusual noises during operation
• Mixing attachments not spinning properly
• Visible cracks or damage to the housing
• Leaking grease from the transmission area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Metallic Chrome

This silver Planetary assembly is the lower drive unit of a stand mixer that carries the beater shaft. Replacing a worn or loose planetary restores smooth, consistent planetary motion and reliable attachment rotation for dependable mixing performance.

• Transfers motor power to the beater and creates true planetary mixing action
• Houses the beater shaft and interfaces with the lower gear train
• Helps maintain stable beater-to-bowl alignment at the bottom of the mixer head
• Typical failure symptoms: beater not turning or stalling, grinding/clicking from the lower head, or noticeable wobble/excess play in the planetary

• Unplug the mixer and remove the bowl and beater before service
• Drive out the roll pin to remove the old planetary; transfer and reuse any model-specific hardware
• Clean and re-grease gears with food-grade mixer grease during reassembly, if needed
• Reinstall the planetary and pin; verify beater-to-bowl clearance per the owner's manual before use