Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Shelf tilting or slipping? This support stud anchors your refrigerator shelf to the liner wall, preventing drops and keeping shelves level. Easy DIY fix.
Myself Read more
Directs defrost water to the drain line in your refrigerator. Replace if cracked, broken, or leaking to prevent water buildup inside the unit.
Fix leaking or slow water flow to your ice maker and dispenser. This water inlet valve controls fresh water supply. Moderate DIY repair in 30–45 minutes.
With part I purchased from Appliance Part Pros Read more
Replace a cracked, broken, or leaking 1/4" water tube in your refrigerator. This cut-to-fit tubing connects internal water components. Easy DIY fix.
Replaced filter housing, and both water tubes Read more
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
This rubber boot seals and shields a component or connector within the appliance. Replacing a worn boot helps keep out moisture and debris, preventing corrosion and wear so the protected part continues to operate reliably.
New auger motor, shaft, and washer fixed it for about $120 , repair people quoted $500 Read more
Grey decorative cap that covers the water filter housing on side-by-side refrigerators. Replace if cracked, broken, or missing for a finished look.
I replaced the pads on my Kitchenaid side-by-side. I was able to order ones that looked exactly like the old ones. It was even easier than what I had seen in a YouTube video. Read more
Ice dispenser door stopped working? This coupling connects the drive motor to the dispenser door mechanism. Replace a broken coupling to restore ice dispensing.
My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday... Read more
Replacement crisper drawer for your refrigerator's produce compartment. Restores organized storage for fruits and vegetables when original is cracked or broken.
Replaces a cracked, worn, or unresponsive dispenser pad on your refrigerator door. Installs in the front dispenser housing for water and ice.
Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more
Ice falling out of dispenser or chute door won't close? This door chute directs ice flow and seals properly. Typical 30-minute DIY fix for dispensers.
Replaced tired motor and chute door seal plate... Through outside of unit door - I have worked in the appliance repair field for years Read more
Ice bin won't release or latch broke? This ice bin latch spring provides tension to secure the ice container properly. Easy 10-minute DIY fix.
Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more
Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more
Replacement support stud that holds refrigerator shelves securely in place. Needed when original peg is broken, cracked, or missing from shelf wall.
Secures refrigerator door handles to mounting studs. Replace if stripped, missing, or unable to hold handle firmly in place. Uses small allen wrench.
Rather than fighting the set screw, I ordered a new handle and extra parts to fix it. My father taught me to use anti seize which I used on all the threaded materials. Appliance parts and all the parts listed easy to see and Order Read more
Secures the bottom grille to your refrigerator frame. Replace if the original clip is cracked, broken, or missing and the grille won't stay in place.
Ordered parts, watched the videos on your website. Very simple. Read more