Ksm96mf - Serial W915676603 Parts

This small drive gear transfers motor power to the rest of the gear train. Replacing a worn or stripped pinion restores smooth, consistent rotation and helps prevent additional damage to neighboring gears and shafts. What it does:

• Engages the mating gear to transmit torque from the motor
• Drives the output gear train for consistent movement
• Maintains proper gear mesh inside the drive housing
• Typical failure signs: grinding/clicking, slipping under load, or no movement of driven parts

• 1 pinion gear

• Disconnect power before servicing; allow all moving parts to stop
• Access the gearcase/drive housing and note the original gear's orientation
• Inspect mating gears; replace as needed and use manufacturer-approved grease if required
• Hand-rotate the assembly to verify smooth operation before reassembly and test

This planetary drip ring fits around a stand mixer's planetary assembly to cover the gap below the gearcase and help catch grease residue, restoring a clean, finished look where the beater hub meets the mixer head.

• Mounts at the base of the mixer head around the planetary housing
• Helps deflect incidental gearbox grease residue away from the bowl area
• Covers the seam between housing and planetary for a clean, finished appearance
• Replace if bent, cracked, loose, missing, or if you notice grease spotting beneath the planetary

• Unplug the mixer and remove the bowl and attachments
• Gently pry off the old ring; clean the seating surface of debris or residue
• Align and press the new ring evenly until fully seated; avoid deforming the ring or striking the gearcase
• On some models, access may require lowering/removing the planetary

This vertical center shaft aligns and drives the rotating components in the refrigerator's ice dispenser/crusher assembly, helping cubes and crushed ice dispense smoothly. Replacing a worn or stripped shaft restores reliable dispensing performance.

• Centers and supports the crusher/dispenser components for smooth operation
• Transfers drive from the dispenser motor through the crushing mechanism
• Helps prevent jams and binding caused by misalignment or wear
• Common symptoms: ice not dispensing, no crush function, grinding/clicking noises, wobbling shaft or visible wear

• Unplug the refrigerator before servicing; handle sharp crusher blades with cut-resistant gloves
• Remove the ice bin and disassemble the crusher housing on a flat work surface
• Note the order of blades, spacers, washers, and any clips; transfer them to the new shaft in the same sequence
• Reinstall the bin, ensure the drive coupling engages fully, restore power, and test dispensing

This black brush holder cap threads into the motor's brush holder to secure the carbon brush and spring. Replace a cracked, stripped, or missing cap to protect the brush assembly and help maintain reliable motor operation. What it does:

• Retains and covers the carbon brush and spring inside the brush holder
• Threads in to provide access for routine brush service
• Helps maintain stable brush contact and reduce intermittent operation from a loose or missing cap
• Typical symptoms: cap is cracked/missing, won't tighten, or the unit runs intermittently after brush service

• 1 black brush holder cap

• Disconnect power before servicing
• Use a flat-blade screwdriver or coin to remove the old cap
• Inspect brush length and seating; install the brush in the same orientation as removed, then hand-tighten the cap—do not overtighten
• If brushes are worn, replace both brushes as a pair for best results

4.5 Quart Polished Stainless Steel Mixing Bowl with Handle for Tilt Head mixers, has enough capacity to mix dough for 6 dozen cookies, 3 loaves of bread or 6 pounds of mashed potatoes in a single batch. Dishwasher-safe for quick and easy cleanup The Stainless Steel Mixing Bowl fits Kitchenaid Stand Mixer models K45SS, KSM75 and KSM95.

Motor brush holder includes illustration numbers: 28, 32, 33, 34, & 46.

This flat spring restores proper tension and return action in the mechanism it supports. Replace a fatigued or broken spring to bring back crisp movement and keep linked parts aligned so the assembly operates smoothly.

• Applies return tension to a lever, cam, or latch so it moves back to its rest position
• Helps maintain alignment and engagement between mating parts during operation
• Can resolve weak or missing spring action, sticking controls, and inconsistent operation
• Replaces a worn, bent, or broken spring to restore designed feel

• Disconnect power to the appliance before servicing; shut off water supply if applicable
• Note the spring's orientation and mounting points before removal
• Use needle-nose pliers for control; avoid overbending to prevent premature fatigue
• Confirm smooth return action before reassembly

This black control lever knob replaces a cracked, worn, or missing knob, restoring a secure grip and clean, factory look so you can adjust settings comfortably and accurately.

• Attaches to a control lever to provide a comfortable, secure handhold
• Enables smooth, precise selection of settings during use
• Helps keep the lever aligned and easy to operate
• Typical symptoms: knob cracked, stripped, loose, missing, or cosmetically damaged

• Disconnect power before servicing for safety
• Remove the old knob from the lever stem; retain any small hardware if present
• Align the new knob and press or thread it onto the stem until fully seated
• Move the lever through all positions to ensure proper engagement before use

This genuine replacement gear is a drivetrain component that transfers motor rotation to a mating mechanism inside your appliance. Replacing a worn or stripped gear restores smooth, reliable motion and helps prevent damage to adjacent parts.

• Meshes with adjacent gear(s) or a shaft to drive an internal mechanism
• Worn or rounded teeth can cause slipping, skipping, or no movement
• Intermittent or stalled movement can indicate a stripped or damaged gear

• Disconnect power (and shut off water/gas if applicable) before servicing
• Access the assembly; note orientation and timing marks
• Transfer any spacers, keys, or retaining clips from the old gear
• Seat the new gear fully and verify smooth manual rotation before restoring power

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet operation. Replacing a worn bearing restores proper alignment and helps prevent noise and premature wear on connected parts.

• Provides a low-friction surface for smooth rotation
• Helps keep the rotating component centered and stable
• Reduces vibration and operating noise
• Common failure signs: grinding/squealing, wobble or play, rough or intermittent rotation

• Disconnect power; also shut off water or gas supply if applicable
• Access the assembly per your model's service information and note part orientation before removal
• Inspect the shaft/hub and any spacers or seals for wear; replace related worn components
• Seat the bearing squarely—do not force; apply only manufacturer-specified lubricant if called for in service literature

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

This brush holder housing secures and insulates the carbon brush inside the motor, helping it maintain steady contact with the commutator for consistent power and speed. Replacing a cracked or heat-damaged holder can reduce arcing and intermittent operation. What it does:

• Holds the carbon brush in proper alignment and provides electrical insulation
• Maintains spring pressure so the brush rides the commutator smoothly
• A worn or damaged holder may cause intermittent start/stop, excessive sparking, or erratic speed
• Visual clues include cracks, heat distortion, or a brush that sticks/binds in the holder

• 1 brush holder housing

• Disconnect power and allow the motor to cool before servicing
• Access the brush assemblies and install the housing in the same orientation as the original
• Ensure the brush moves freely in the holder and makes firm contact; inspect brushes for wear and replace if needed
• Many motors use two brush holders—inspect the opposite side and replace as needed for even performance

This headless, cup-point set screw secures a component to a shaft or hub inside your appliance. The 1/4-28 x 3/8 in size bites into the mating surface to prevent slipping, helping keep collars, pulleys, or knobs aligned and stable.

• Locks a hub, collar, or pulley to a shaft to prevent movement
• Helps maintain alignment and reduce wobble or vibration
• Replaces missing, stripped, or damaged set screws
• Common signs include components slipping on a shaft, rattling noises, or recurring loosening

• Disconnect power before servicing
• Clean threads and align with any flat on the shaft before tightening
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Recheck tightness after a brief test run

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)

This bearing supports a rotating shaft within the appliance's drive system, keeping components aligned and allowing smooth, quiet operation. Replacing a worn bearing can reduce grinding noises and restore reliable performance.

• Supports and centers a rotating shaft to reduce friction
• Helps maintain proper alignment of gears/shafts for smooth operation
• Worn bearing symptoms: grinding or squealing, excess play/wobble, rough or stalled rotation
• Can contribute to heat buildup or metal debris when failing

• Disconnect power before servicing
• Disassemble the housing/gearcase as needed to access the bearing; note part orientation
• Press the bearing in/out with a proper driver; avoid striking races or deforming the housing
• Clean out old grease and re-lubricate per the manufacturer's service guidelines; inspect related gears and seals

This factory fastener secures appliance panels, brackets, and components. Replacing a missing or worn screw restores a tight, rattle-free fit and helps keep parts aligned as designed for reliable operation. What it does:

• Fastens specified components to maintain alignment and structural integrity
• Helps reduce vibration, noise, and loosening from normal use
• Replace if stripped, corroded, or missing
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power and shut off water or gas before servicing
• Match location and orientation; replace one-for-one with the original
• Start threads by hand to avoid cross-threading; use the correct driver bit and do not overtighten
• Inspect related clips/inserts; replace if damaged to ensure proper retention