Ksss42mdxoo Parts

The Defrost Thermostat is an OEM part for Whirlpool refrigerators. The thermostat monitors the temperature of the evaporator coil and signals the defrost heater to turn on or off to prevent frost buildup, ensuring efficient cooling.

Causes of a bad defrost thermostat can include wear and tear over time, exposure to extreme temperatures, or electrical malfunctions.  

Symptoms of a bad defrost thermostat include:

• Excessive frost buildup in the freezer
• The refrigerator not maintaining the correct temperature
• The defrost heater not activating
• The refrigerator running continuously or not running at all

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specs: 10-16 x 1/2 inch.

Size: 8 x 1/2 ab.

Size: 1/4 inch. Nut for plastic water line.

This part shields and positions the temperature control's sensing bulb inside the control housing, helping the control respond accurately and keep cabinet temperatures stable. Replace a cracked, deformed, or missing barrier to restore consistent, predictable cooling. What it does:

• Shields the cold-control thermostat/capillary bulb from direct airflow
• Helps the temperature control sense average compartment temperature and cycle correctly
• Supports steady temperatures and normal run times
• A damaged or missing barrier may contribute to temperature swings or frequent control adjustments

• 1 thermostat barrier

• Disconnect power before servicing
• Access the control housing; remove the dial/cover and any retaining screws or clips
• Note the factory routing of the thermostat capillary; install the barrier without kinking or sharply bending the sensor tube
• Reassemble, set controls to mid-range, and allow up to 24 hours for temperatures to stabilize

This door shelf trim is the front bar that snaps onto a refrigerator's door bin to keep bottles and containers secure. Replace a cracked or missing retainer to restore safe, organized storage on the door.

• Attaches to the door shelf/bin to hold items in place during door movement
• Restores function when the original bar is cracked, broken, warped, or missing
• Helps prevent items from sliding or falling from the door
• Common symptoms: loose or broken trim, bar won't stay attached, door shelf won't hold items properly

• Disconnect power and remove items from the affected shelf before service
• Release the old bar (squeeze tabs or slide ends free), align, and snap the new trim onto the door shelf/end caps
• Allow cold plastic to warm to room temperature to reduce risk of cracking
• Verify secure engagement before reloading the shelf

This Power Disconnect Switch is the refrigerator's on/off service switch. It interrupts incoming power when actuated, allowing safe servicing or resetting of the unit without unplugging it and helping prevent unintended operation when access panels are open. What it does:

• Interrupts electrical power to the unit when switched off or tripped
• Provides a dedicated service disconnect for safe maintenance and resets
• Common symptoms: no power, intermittent shutdowns, or the unit won't stay on unless the switch is held/positioned
• Visual clues: broken actuator or heat-discolored/loose terminals

• Power disconnect switch only

• Disconnect power at the breaker before servicing
• Access the switch location; on many built-in units it's behind the top grille or control panel
• Move wires one at a time to the new switch to maintain correct orientation
• Restore power and verify the switch cleanly turns the unit on and off

This refrigerator door gasket compresses against the cabinet to create an air-tight seal. Replacing a worn gasket helps keep cold air in, maintain set temperatures, reduce moisture and frost, and support overall efficiency.

• Forms a continuous perimeter seal so the door closes snugly against the frame
• Helps maintain consistent internal temperatures and proper humidity
• Reduces frost/ice buildup and exterior condensation around the door area
• Signs of failure can include torn or warped rubber, visible gaps, condensation or frost near the door, longer run times, or warming inside the compartment

• Unplug the refrigerator and clear items from the door for easier handling
• Warm the new gasket (room temperature, or gently with a hair dryer on low or warm water) to relax folds—do not overheat
• If retained by screws, loosen the inner-liner retainer, seat the gasket lip starting at the corners, then tighten evenly; for push-in styles, press fully into the channel
• After installation, verify uniform contact all around and adjust door hinges if needed; allow up to 24 hours for the gasket to fully conform

Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.

The Screw is an OEM part for Whirlpool refrigerators. This screw plays a small but important structural role, securely fastening the refrigerator door hinges in place.

Causes of a bad screw include normal wear and tear, repeated door opening/closing stress, or accidental damage during cleaning or servicing of the hinge area.

Symptoms of a bad hinge screw include:

• Loose or sagging door that does not close or seal properly
• Increased vibration or noise from the hinge area
• Difficulty opening/closing the door smoothly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does

• Forms a reliable seal between components to prevent fluid or air leaks
• Maintains proper operation by keeping the sealed area contained
• Replaces gaskets that are brittle, cracked, flattened, or swollen
• Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal

• 1 gasket/seal

• Disconnect power and any water or gas supply before servicing
• Note the gasket's orientation; compare old and new parts before installation
• Clean and dry mating surfaces; remove old adhesive and debris
• Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This is the replacement cover for the refrigerator crisper lid. It restores a clean, finished edge and proper lid operation over the crisper bin so drawers open and close smoothly and contents remain covered.

• Replaces a broken or missing cover on the crisper-lid assembly
• Provides a finished surface and correct fit for the lid above the crisper drawer
• Helps prevent the lid from binding, popping off, or failing to close
• Common symptoms: cracked/missing piece, lid misalignment, difficulty opening/closing the crisper

• Disconnect power before servicing
• Remove food and crisper drawer(s) for clearance
• Release any screws or locking tabs, remove the damaged cover, and retain hardware as needed
• Align the new cover and secure it; avoid forcing plastic parts

These inserts are for 1/4 inch plastic tubing. Package of 4.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.