Kud530fx552 Parts

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

12 Ft in length

The Lower Rack Wheel is an OEM part for Whirlpool dishwashers. It attaches to the lower dishrack, allowing it to glide in and out smoothly during loading and unloading. For the matching wheel axle, order 4162321.

You should replace the lower rack wheel if it becomes worn out or damaged. Causes of a bad lower rack wheel can include regular wear and tear from frequent use, exposure to high temperatures and detergents, or physical damage from impacts or heavy loads. A faulty wheel can hinder the movement of the lower rack, making it difficult to access and load dishes properly.

Symptoms of a bad lower rack wheel include:

• The lower rack not sliding smoothly or getting stuck
• Uneven or lopsided positioning of the lower rack
• Noise or resistance when moving the lower rack
• The wheel appearing cracked, broken, or missing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This replacement screw secures appliance components in place. Swapping a stripped, rusty, or missing fastener restores a tight fit for panels, brackets, and handles, helping reduce vibration, rattling, and premature wear.

• Secures panels, brackets, trim, or hardware to the appliance frame
• Replaces missing, stripped, or corroded fasteners that no longer hold
• Helps eliminate looseness, rattling, or misalignment
• Restores proper fit and finish after service

• Disconnect power; shut off water supply if servicing a dishwasher.
• Match thread and length to the original screw before installing.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• When applicable, replace paired screws together for even clamping.

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

Replacement spring kit that restores proper tension and balance to appliance doors and lids, helping them open and close smoothly and stay in position. Use this kit to replace worn or broken springs that cause sagging or noisy operation. What it does:

• Replaces worn or broken door/lid springs to restore proper tension and balance.
• Helps the door or lid open and close smoothly and remain in the desired position.
• Reduces sagging, bouncing, slamming, and related noise caused by failed springs.
• Prevents additional wear on hinges and closures by restoring correct alignment and support.

• Disconnect power (and water, if applicable) before starting any repair; follow all safety instructions in the appliance manual.
• Support the door or lid during removal and installation to avoid pinch or crush injuries.
• Use proper hand protection and tools; keep small fasteners organized to avoid loss.

Also Order Spray Arm Seal

Almond. Size: 13 oz. can. Acrylic appliance paint.

Fits most Kitchen Aid dishwashers. Replaces old 2 coil valves.

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Color: Almond

The Whirlpool dishwasher mounting bracket is an OEM replacement part responsible for securing the dishwasher in place and attaching it to the surrounding cabinetry or countertop. It provides stability and support to the dishwasher during operation, preventing it from moving or tipping over.

Causes of a bad bracket can include normal wear and tear, corrosion due to prolonged exposure to water and detergents, or physical damage from accidental impact or improper handling during maintenance.

Symptoms of a bad bracket include:

• Loose or misaligned internal components
• Increased noise during operation
• Parts shifting or moving out of place during the wash cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.