Kuds30fxpa3 Kitchenaid Parts

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

This power cord connects your appliance to a household outlet. Replacing a worn or damaged cord restores safe, reliable power and can help resolve no-power or intermittent power issues caused by a compromised lead.

• Delivers electrical power from the outlet to the appliance
• Replaces cords with cracked, frayed, or heat-damaged insulation or a damaged plug
• Helps when the unit won't power on or loses power when the cord is moved
• Addresses visible scorching, arcing, or melting on the cord or plug

• Disconnect power before servicing; verify no voltage is present
• Note wire positions or take a photo before removal; match to the same terminals on install
• Use the proper strain relief/clamp and route away from sharp edges, moving parts, and heat sources
• Confirm the ground connection is secure; do not modify the plug

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.

• Screens large food particles and debris from the pump/chopper inlet
• Helps maintain proper water circulation and consistent cleaning performance
• Reduces risk of pump damage or noisy operation from debris
• Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack and spray arm; access the sump/accumulator area per your model
• Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
• Reassemble and ensure the screen sits flat with no gaps

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

Color: Stainless   Note: Comes with Allen wrench, spare set screw, and instructions.

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

This vent door bezel is the trim piece that frames the vent opening on the dishwasher door. It restores a clean, finished look and helps keep the vent assembly properly seated if the original bezel is cracked, loose, or missing.

• Mounts on the exterior of the door around the vent outlet
• Provides a finished edge and helps retain the vent assembly/gasket
• Replaces damaged or missing trim that won't stay attached
• Common symptoms: broken tabs, loose or rattling vent trim, visible gap or cosmetic damage around the vent

• Disconnect power to the appliance; turn off water supply if needed
• Open the door and remove fasteners to access the vent area behind the panel
• Release the old bezel (tabs/screws), align the new bezel, and secure flush to the panel
• Do not overtighten fasteners; avoid vibration or leaks

This replacement screw secures appliance panels, brackets, and internal components. Install it when original hardware is missing, stripped, or corroded to restore a solid, factory hold and help stop vibration, rattles, and misalignment.

• Provides secure attachment for covers, brackets, and assemblies
• Replaces missing, damaged, or rusted hardware
• Helps resolve loose panels, buzzing/rattling noises, or shifting parts
• Supports proper alignment and reliable operation when tightened correctly

• Disconnect power; shut off gas/water if applicable before service
• Match thread and length to the original; replace in the same location
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If washers, spacers, or threadlocker were present originally, transfer or replace them