Kv25g0x Parts

This planetary assembly restores the mixer's planetary mixing action by linking the gearcase to the beater shaft. It replaces a worn or damaged lower hub to deliver smooth, consistent attachment rotation. Finish: imperial gray.

• Drives the beater/attachment shaft with true planetary motion
• Transfers power from the internal gear train to the attachments
• Helps maintain proper alignment of the lower hub
• Resolves: beater not turning, slipping, grinding/clunking from the front, or visible wobble/damage at the planetary hub

• Disconnect power; remove bowl and attachments before service
• Protect the finish; remove the drip ring to access the retaining pin
• Drive out the planetary retaining pin, slide off the old assembly, and align/install the new one
• Seat the pin fully and verify smooth rotation before reassembly and testing

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This rubber foot replaces a worn or missing foot on the base of a stand mixer. It helps stabilize the mixer, reduce vibration and movement, and protect your countertop so the mixer stays steady during use. What it does:

• Provides non-slip grip to help prevent the mixer from sliding
• Cushions and helps reduce vibration
• Helps keep the mixer level for consistent operation
• Common symptoms include wobbling/rocking, "walking" on the counter, and scuff marks on the surface

• 1 rubber foot

• Unplug the mixer and remove the bowl/attachments before beginning
• Lay the mixer on a padded surface to access the base
• Pull the damaged foot straight out; clean the recess if needed
• Press the new foot fully into the hole until seated flush; replace additional feet as needed to keep the mixer level

This small retainer clip secures the drip bowl and coil surface element so they stay properly seated on the cooktop. Replacing a worn or missing clip restores a tight, level fit and reduces wobble during use. What it does:

• Holds the drip bowl to its mounting point and helps keep the surface element seated
• Maintains alignment to reduce movement and rattling
• Helps prevent the element from tilting so cookware sits more evenly
• Common symptoms: loose or wobbly burner/bowl, bowl won't stay seated, or a cracked/missing clip

• Retainer clip only

• Disconnect power at the breaker before servicing
• Lift out the coil element and drip bowl; note clip orientation for reassembly
• Snap the new clip into place carefully—avoid over-flexing the part
• Reinstall the bowl and element and ensure the burner locks in and sits level

This small retaining pin secures the bowl retainer/clip so the mixing bowl locks firmly in place during operation. Replace it if the original pin is missing or bent, or if the bowl won't stay seated. What it does:

• Anchors the bowl retainer/clip to the frame
• Keeps the bowl locked and stable during use
• Helps reduce bowl wobble, vibration, and rattling
• Common symptoms: bowl won't latch, rocks loose, or visible pin damage/missing

• 1 retaining pin

• Disconnect power before servicing
• Remove the bowl and access the bowl retainer/clip
• Support the casting; drive the old pin out with a small punch—avoid prying against the housing
• Align holes and install the new pin flush; verify the bowl latches securely and adjust the retainer per your model's service guide

Replacement cam that restores proper engagement of the appliance's mechanical linkage so cycles run smoothly. Installs where the drive/shift mechanism needs a correctly timed cam to stop slipping or misalignment. What it does:

• Transfers rotary motion to the linked component so parts engage at the correct time
• Restores reliable engagement to reduce skipping, grinding, or irregular cycle behavior
• Commonly replaced if cracked, worn, or otherwise fails to engage properly
• Matches the OEM part name and fit as a direct replacement when the original cam is damaged

• Always disconnect power (and water, if applicable) before starting service
• Remove required access panels and note the original cam orientation for correct reassembly
• Inspect mating parts (shaft, clips, splines) and replace any damaged hardware before installing the new cam
• Reassemble panels and run a test cycle to ensure normal operation and correct engagement

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

This 6-32 machine screw is a direct-fit fastener used to secure appliance panels and components. It provides a reliable replacement for stripped or missing screws to restore proper fit and reduce vibration or looseness. What it does:

• Secures panels, brackets, and internal components to keep parts aligned and stable
• Restores proper fastening when original screws are missing, stripped, or damaged
• Helps eliminate rattling or movement caused by loose fasteners
• Compatible with metal-to-threaded-hole connections that use 6-32 hardware

• Use the correct driver and avoid over-tightening to prevent stripped threads or damaged components
• Disconnect power and follow appliance safety guidelines before servicing
• If threads are damaged, replace both screw and any damaged insert or nut as needed

The Power Cord is an OEM component specifically designed for Whirlpool stand mixers. Located at the rear base of the mixer, it safely delivers current to operate mixing attachments, speeds, and functions. 

Causes of a bad power cord include cracking or pulling at the entrance/exit points over years of use. Acute damage like punctures or burns requires replacement.

Symptoms of a faulty power cord include:

• Loose, interrupted connections when plugged in  
• Exposed or frayed internal filaments
• Tripping circuit breakers more frequently
• Buzzing, zapping, or dead mixer response

This OEM Whirlpool replacement cord ensures problem-free current transmission. Installed promptly, it prevents shock risks or fire hazards due to compromised integrity.  

Compatible also with some KitchenAid and Proctor Silex mixers, this part maintains crucial convenience and performance. Protect your valued kitchen tool with an OEM power cord replacement as needed.

This is the planetary assembly for select stand mixers. It's the lower drive that holds the beater shaft and transfers power from the gearcase to rotate the beater for efficient mixing.

• Transfers torque from the mixer's gear train to the beater shaft
• Supports smooth, consistent beater rotation
• Worn planetary can cause wobbling beater, grinding/rumbling noises, poor mixing, or intermittent beater motion
• Needed if the beater shaft has excessive play or the gear teeth are damaged

• Unplug mixer before servicing; remove bowl and attachment
• Head must be opened to access and remove the retaining pin/fasteners
• Support the lower assembly when separating it from the gearcase to avoid damage
• Re-grease gears if specified by the service manual and proper beater-to-bowl clearance after reassembly

This band trim is a cosmetic finishing piece that covers and protects the visible edge of the appliance door or cabinet for a clean, factory look. It refreshes appearance and helps keep dirt and moisture out of the seam. What it does:

• Covers and finishes the exposed edge of a door or cabinet for a uniform appearance
• Helps reduce dirt and grime buildup along the seam between panels
• Restores a worn, scratched, or missing trim to improve overall appliance appearance
• Works with existing door/cabinet mounting points to sit flush with surrounding surfaces

• Disconnect power to the appliance before starting repairs and work on a cool, dry surface
• Remove any clips or fasteners holding the old trim; save reusable hardware
• Align the new trim with the edge and press or secure into place using the original mounting points
• Replace them with OEM-specified hardware

The Transmission Housing is an OEM part for Whirlpool mixers. This component encases the transmission, which is responsible for transferring power from the motor to the mixing attachments. The housing ensures the transmission is protected from external damage and maintains the alignment and stability of internal components.

Over time, the transmission housing can become compromised due to regular use, exposure to food and moisture, or accidental impacts. Damage to this part can lead to misalignment, which affects the performance of the mixer.

Symptoms of a bad transmission housing include:

• Unusual noises during operation
• Mixing attachments not spinning properly
• Visible cracks or damage to the housing
• Leaking grease from the transmission area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Sleeve Bearing is an OEM part for Whirlpool mixers. This component provides critical support for the mixer's motor shaft, allowing it to rotate smoothly and efficiently. By reducing friction and wear, the rear sleeve bearing ensures that the mixer operates quietly and reliably, extending the lifespan of the motor and other moving parts.

You should replace the rear sleeve bearing if it becomes worn or damaged. Causes of a bad rear sleeve bearing can include regular wear and tear from frequent use, lack of lubrication, or the accumulation of debris. Over time, these factors can lead to increased friction, noise, and potential motor damage.

Symptoms of a bad rear sleeve bearing include:

• Unusual noises such as squeaking or grinding during mixer operation
• The mixer shaft not rotating smoothly or becoming difficult to turn
• Increased vibration or wobbling of the mixer attachment
• Excessive wear or damage to the motor shaft

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Planetary Assembly is an OEM replacement part for Kitchenaid stand mixers. It is the central component that transmits rotational power from the motor to the mixing attachment through an intricate system of gears.

Causes of a bad planetary assembly can include worn gears that no longer mesh properly, broken or missing gear teeth from overloading, or a failed bearing.

Symptoms of a bad planetary assembly include:

• Slipping or jumping of gears during mixing
• Grinding or scraping noises
• Inability to mix thoroughly on higher speeds
• Premature failure of the motor

This OEM replacement is also compatible with Maytag, Whirlpool, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Metallic Chrome