Maytag Lse7806ace Parts

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

This mechanical washer timer controls the sequence and duration of wash, rinse, and spin cycles. Replacing a worn timer restores proper cycle advancement and consistent operation when the washer stalls, skips steps, or only progresses when the knob is turned.

• Controls and sequences power to the drive motor, water inlet valves, and drain pump per the selected cycle
• Advances the machine through fill, agitate, drain, rinse, and spin intervals
• Provides internal contacts that start/stop each step and signal the next stage
• Common symptoms: no cycle advance, stopping mid-cycle, intermittent operation, or advancing only when manually turned

• Disconnect power before servicing; do not work on a live appliance
• Access the control console; remove the panel/cover to reach the timer
• Photograph and transfer wires one at a time to matching terminals to avoid miswiring
• Mount the new timer securely and align the shaft with the knob/dial before reassembly

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This washer injector (lower) forms the bottom half of the fill injector assembly, channeling incoming water cleanly into the tub. A damaged injector can cause leaks or spray at the tub ring during fill. What it does:

• Directs fill water into the tub through the injector assembly
• Seals with the upper injector to prevent splashback
• Common symptoms: leaking or spraying during fill, water on floor near the top/front during fill, visible cracks/warping on the injector
• Restores a clear, sealed water path for proper filling

• One lower injector

• Disconnect power and shut off water supply before servicing
• Access may require lifting the top or removing the cabinet to reach the injector at the tub ring
• Transfer any reusable clamps/retainers; align with the upper injector for a proper seal
• Run a short fill and inspect for leaks after installation

This bolt is a genuine Whirlpool part, sold individually. It can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This bolt fastens parts to one another in conjunction with a nut so that they do not come loose while the washing machine vibrates when it is in operation.A bolt might be easily lost or misplaced as it is a small part that might go missing without any noticeable symptoms. Additionally, a bolt might be stripped through general wear and tear or as a result of a direct impact collision with a hard object that warps the component beyond functionality. If any of these things occur, the bolt should be replaced by this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bolt is compatible with the following appliance brands: Whirlpool, Maytag, International, and Jenn Air.

This is the main drive motor that powers the appliance's drive system. A failing motor can cause the unit to stop agitating or spinning, run intermittently, hum without movement, or trip the overload.

• Converts electrical energy into mechanical rotation for the drive system
• Common failure symptoms: no spin, no agitation, humming/buzzing, burning odor, or intermittent operation
• Diagnosed when the basket won't move but the control powers on
• Often associated with tripped thermal/overload or blown motor windings

• Disconnect power before servicing; verify capacitor discharge where applicable
• Note wire locations and harness orientation before removal
• Inspect belt, pulley, coupling, and wiring for wear or heat damage; replace as needed
• After installation, run a short cycle to ensure proper rotation and operation

This stop lug is a small, molded limiter that prevents over-travel of a moving control or mechanism in your washer, helping components stop in the correct position for consistent, reliable operation.

• Acts as a positive stop to limit movement of a mating part
• Helps maintain proper alignment and protects components from over-rotation
• Symptoms of a worn or missing lug can include excessive play, over-travel, or a control that doesn't stop where it should
• Visible damage or a missing lug indicates replacement is needed

• Disconnect power and water supply before servicing
• Access the mounting area and note the original orientation
• Seat the new lug fully and secure per the original configuration
• Reassemble and test that the mechanism stops at the intended position

This transmission pinion is the small drive gear inside the gearcase that meshes with the mating gear to transfer motor power through the drive. Replacing a worn pinion restores smooth operation and reliable torque delivery.

• Transfers rotation from the motor through the gear train inside the transmission
• Helps maintain proper speed and torque to the drive output
• Replaces stripped or broken teeth that cause slipping and chatter
• Typical symptoms: grinding/clicking noises, output that stalls or won't turn, metal shavings in grease

• Unplug the appliance before servicing; allow all moving parts to stop
• Access requires opening the drive housing/gearcase; note the orientation of shims, washers, and spacers
• Clean out old grease/debris and re-pack with manufacturer-approved grease
• Inspect mating gears, bearings, and shafts for wear; replace related parts as needed and follow the service manual for alignment

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.