Maytag Lse7806ace Parts

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

Size: 10-32

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed

This pin collar is a small retaining fastener that secures a shaft or component in place, preventing lateral movement and keeping assemblies aligned for reliable operation. It's a simple replacement to restore proper fit and function. What it does

• Retains shafts, pins, or small components to prevent sliding or separation
• Helps maintain alignment of moving parts for smooth operation
• Commonly replaced when parts shift, wobble, or fall out of position
• Works as a low-profile mechanical stop in various appliance linkages

• Pin collar (single)

• Disconnect power to the appliance before beginning any repair
• Verify orientation and seating against the mating part; install so collar fully engages the shaft or groove
• Use appropriate tools and avoid hammering or forcing the part to prevent damage
• Reinstall retaining rings or additional hardware in the original order

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

This replacement dryer timer controls the sequence and duration of drying cycles so your dryer runs the selected program and advances between cycle steps. It restores timed cycle control when the original timer is worn or fails. What it does:

• Rotates through cycle settings to start, run, and advance drying programs
• Sends signals to heat, motor, and other controls at the proper times
• Can cause no start, no cycle advance, or incorrect cycle behavior when faulty
• Works as the user-selected time/control interface for manual cycle selection

• Disconnect power to the dryer before attempting service to avoid shock or injury.
• Access may require removing the control console or rear panel; retain screws and note connector locations.
• Transfer any knobs or bezels as needed and reconnect wiring harnesses in original positions.
• After installation, test all cycle settings and safety features.

This electronic control board regulates the appliance's functions and user controls so the unit runs cycles and displays status correctly. Replaces a failed control board to restore normal appliance operation and control responsiveness. What it does:

• Manages timing, cycle selection, and user interface commands for the appliance
• Communicates with sensors and actuators to start and stop cycles
• Can resolve symptoms like unresponsive controls, incorrect cycle operation, or error codes tied to the main control
• Works as the central logic module coordinating other control components

• One electronic control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available
• Verify cabinet access panels and connectors match before installing the replacement

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This PC switch senses the washer lid position and tells the control when the lid is open or closed so the washer operates safely. It replaces a worn or failed lid position sensor to restore normal cycle starts and door-safety behavior. What it does:

• Detects lid open/closed status and signals the control board
• Prevents washer from starting or spinning when lid is open
• Can correct symptoms like no-start, no-spin, or interrupted cycles when the lid is closed
• Works as the user-accessible lid position safety switch used by the control

• One PC switch

• Disconnect power before beginning any service to avoid shock or injury
• Access may require removing the washer top or control console
• Observe wiring orientation and connector placement; transfer connectors exactly or label before removal
• Test operation after install and reassemble panels securely

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

This replacement bolt is a direct-fit fastener used to secure appliance components. It restores proper fastening to reduce movement and noise while keeping parts aligned for safe operation. What it does

• Secures panels, brackets, or assemblies to prevent loosening and rattling
• Restores proper alignment of mounted components after repair or maintenance
• Helps maintain safe operation by keeping parts firmly attached
• Common symptom: loose or missing bolt causing vibration or parts shifting

• One replacement bolt

• Disconnect power before servicing the appliance to avoid electrical shock
• Use the correct socket or wrench size to avoid stripping the head
• Tighten securely but avoid overtightening to prevent thread damage
• If corrosion or damaged threads are present, replace the mating fastener or insert as needed

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

Color: Stainless steel

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.