Maytag Msd 2651Heb Parts

This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.

• Melts ice from the evaporator coil during the defrost cycle
• Prevents frost buildup that restricts airflow and causes warm spots
• Helps maintain stable refrigerator and freezer temperatures
• Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting

• Disconnect power before servicing; wear cut-resistant gloves
• Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
• Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
• After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control

Size: 1/4 inch. Nut for plastic water line.

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

This arm valve installs in the dishwasher's spray arm feed to control water flow. It helps maintain proper pressure so the spray arm spins and distributes water evenly for effective cleaning.

• Directs water through the spray arm and helps maintain wash pressure
• Prevents unintended backflow that can reduce spray performance
• If worn, stuck, or missing, lead to weak spray or poor cleaning results
• Common signs include intermittent wash coverage or spray arm not rotating as expected

• Disconnect power and turn off water before servicing
• Remove the rack/spray arm or feed manifold to access the valve
• Note the valve's orientation and seat the new valve fully in the same direction
• Reassemble and run a quick cycle to check for proper spray and leaks

Ice maker water line: 1/4x 8ft.

The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.

Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.

Symptoms of a bad shelf stud include:

• Shelves not staying securely in place
• Shelves tilting or collapsing
• Visible cracks or damage to the stud
• Difficulty in inserting or removing shelves

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This cam-door is the small pivoting cam that helps a washer/dryer or laundry door latch and swing smoothly. Replacing a worn or broken cam restores proper door movement and helps the door close and seal reliably. What it does:

• Acts as the pivot/latch cam that guides the appliance door during opening and closing.
• Helps the door engage the latch and maintain correct alignment.
• Commonly used to stop a door from hanging, binding, or failing to stay closed.
• Can reduce door noise or catching caused by a damaged cam.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Support the door or cabinet panel during removal to prevent dropping or damage.
• Remove the door or access panel and replace the cam using basic hand tools; keep track of fasteners.
• After reassembly, check door operation and latch engagement before returning the appliance to service.

Clip for bottom grill. If your original clip is riveted, order screw WP489478.

This dishwasher sump inlet forms the sealed passage between the tub and the pump system, directing wash water out of the basin. Replacing a cracked or clogged inlet helps stop leaks and restores steady water circulation and cleaning performance.

• Channels water from the tub into the circulation/drain system
• Maintains a watertight seal at the tub floor to prevent leaks and air intrusion
• Helps preserve spray pressure and consistent wash performance
• Common symptoms of failure: water leaking under the unit, weak cleaning results, unusual pump noise, visible cracks or warping

• Disconnect power and water supply; wear cut-resistant gloves and place a towel or shallow pan to catch residual water
• Access may require removing the lower spray arm, filters, and toe panel; note hose/clamp orientation before removal
• Clean sealing surfaces before seating the new inlet; secure per model design and ensure all connections are tight
• Reassemble and run a short test cycle while inspecting for leaks

This vent pad cushions and seals the dishwasher's door vent, helping route steam out of the tub while protecting the inner door and control area from moisture. Replacing a worn pad can help stop vent leaks and rattling.

• Creates a seal between the vent assembly and inner door liner to contain moisture
• Helps channel humid air during drying and reduces steam escaping at the vent opening
• Cushions the vent assembly to minimize vibration and noise
• Typical symptoms of a failed pad: steam or water at the top of the door near the vent, moisture inside the console, or a rattling vent

• Disconnect power at the breaker and shut off water before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Note pad placement; install the new pad in the same location with clean, dry mating surfaces
• Reassemble and run a short cycle to check the vent area for leaks

The Dishwasher Upper Rack Kit 4 Pack is an OEM part for GE dishwashers. This kit includes four sets of studs and rollers that attach to the upper rack, allowing it to slide smoothly in and out of the dishwasher. 

Causes of bad studs and rollers can include regular wear and tear, exposure to high temperatures and water, or damage from heavy or improperly loaded items. 

Symptoms of bad studs and rollers include:

• The upper rack not sliding in and out smoothly
• The rack feeling loose or unstable
• Broken or missing studs and rollers
• The upper rack becoming misaligned or difficult to move

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a hose chamber, or dishwasher hose pump. This part attaches to the back of the dishwasher and is the direct line for the water to get in and out during the washing cycle. This specific part prevents leaking and is very important to the machine. The user might need to replace this part if the dishwasher is leaking, if the machine is not putting in or draining water properly, or if the machine has stopped working altogether. Anyone can complete this repair with basic household tools such as a screwdriver, pliers, and working gloves. Always make sure the machine is empty of dishes and is drained of water before starting the repair. Also make sure it is unplugged from the electrical source and is turned off completely. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from manufacturers like General Electric, Hotpoint, RCA, and more.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

Note: Right Hand Roller

Includes screws.