Mvw4505mw Parts

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Motor-Drive is an OEM part for Whirlpool washing machines. It converts electrical energy into rotational motion to power the wash cycle. The motor transmits torque to the inner wash basket or tub through the drive system to clean clothes through agitation and spinning actions. Issues with the motor-drive can negatively impact the entire functionality of the washer.

Causes of failure can be wear and tear over time, damage from oversudsing or unbalanced loads, or exposure to moisture. Ensure your washer keeps running at its best with this OEM Whirlpool replacement part.

Symptoms of a bad Motor-Drive include:

• The washer failing to start or stopping mid-cycle
• Excessive noise or vibration coming from the motor area
• Slow or inefficient spinning
• Inability to advance through cycles

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Lid Lock Bezel (White) is an OEM replacement part for Whirlpool washers. The bezel provides an aesthetic covering for the lid lock mechanism located on top of the washer. 

Causes of a bad bezel can include normal wear and tear from repeated use of the washer lid over time. Scratches, cracks or splits in the plastic material are also possible from accidental impact or drops.

Symptoms of a bad bezel include:

• Cosmetic flaws like discoloration, scratches or cracks that diminish the appearance of the washer
• Looseness, rattling or misalignment of the bezel covering 
• Difficulty opening or closing the washer lid securely. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Tub Ring is an OEM part for Whirlpool washing machines. It is an internal gasket or seal that fits securely around the outer rim of the washer tub. The tub ring works to create a watertight barrier, preventing leakage between the tub and other cabinet components like the agitator shaft or balancer. 

Causes of a bad tub ring can include warping due to heat exposure or tub filling impacts over time, cracks developing from heavy impacts or loads that stress the tub, or cuts and tears caused by debris lodged inside the ring.

Symptoms of a bad tub ring include: 

• Water leaks appearing around the tub or agitator shaft when in use
• Puddles or standing water found inside the washer cabinet 
• Difficulty getting the washer lid or door fully closed and secured
• Excessive moisture buildup inside non-tub areas 

It is also compatible with Maytag, KitchenAid, Amana, Roper, and select Kenmore models.

The Dispenser is an OEM part for Whirlpool washing machines. It holds and dispenses detergent for each wash load through the drawers located on the washer's console panel. 

Symptoms of a bad dispenser include:

• Improper or incomplete dispensing of detergent
• Detergent residue accumulated inside the dispenser 
• Drawers not opening or closing as intended

Causes of a dispenser failure can be due to worn components, mineral buildup interfering with mechanics, or damage from moisture exposure over time. 

Replacing with a new OEM dispenser restores optimal detergent delivery for every cycle. This ensures clothes are fully cleaned and rinsed without risk of detergent residue.  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

Note: Quantity of 1 pad, order as needed. Measures about 3.5" x 3.5".

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Note: 5  Position Switch
 

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes connector and both clamps.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed