Pseed Queen Parts

This rear gasket cover helps seal and protect the rear edge of a refrigerator cover or panel, maintaining a proper barrier to keep cold air where it belongs and prevent moisture or debris intrusion.

• Seals the rear edge of the cover to reduce air leaks
• Helps maintain stable internal temperatures
• Can address issues like warm spots, excess frost, or condensation around the rear cover area
• Replaces a cracked, deformed, or missing rear gasket cover

• Unplug the refrigerator before servicing
• Remove any shelves, drawers, or panels blocking access to the rear cover
• Carefully release retaining tabs/screws, transfer the gasket cover, and seat evenly
• Verify the cover is fully engaged and sealing before restoring power

Color: stainless. It measures about 8 inches wide by 4 inches deep.

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

This freezer shelf trim replaces a damaged or missing edge piece on the freezer shelf. It attaches to the shelf/frame to provide a finished lip that helps contain items and restores the shelf's original fit and appearance.

• Provides the finished edge on a freezer shelf to help keep items from sliding off
• Attaches to the shelf/frame for a secure, correct fit
• Replace when cracked, warped, loose, or missing
• Common symptoms include a broken or jagged shelf edge, trim that won't stay attached, or items slipping off the shelf

• Unplug the refrigerator and remove items from the affected shelf
• Remove the shelf if needed; release and remove the old trim
• Align the new trim with the shelf/frame and press until fully seated and secure
• Do not force parts together; inspect the shelf/frame for damage before reassembly

This slide-out freezer shelf restores a smooth, stable storage surface and easy access in the freezer compartment. Replace a cracked, hard-to-slide, or missing shelf to regain capacity, organization, and the spacing your freezer was designed for.

• Provides a level storage surface and slides forward for better visibility and reach
• Secures into the side supports/rails at the designated freezer position
• Helps maintain intended spacing and airflow between freezer sections
• Typical symptoms: cracked or broken shelf, damaged tabs, won't slide smoothly, sits unevenly, or missing shelf

• Remove items from the area and support the shelf with both hands when removing/placing
• Align with the side supports/rails and slide fully into place; verify correct front/back orientation
• Do not force; ensure it is seated in the correct slots before loading
• Handle edges carefully; wear cut-resistant gloves to prevent injury

The Tube Lead is an OEM part for GE refrigerators. It is responsible for routing water through the unit.

Causes of a bad tube lead can include mineral accumulation restricting flow, loosened compression fittings, or cracked/split tubing exposing water to air.

Symptoms of an issue with the water line tube lead include:

• Slow or inconsistent water and ice production
• Water pressure or temperature fluctuations at the dispenser
• Leaks in the refrigerator's exterior bottom panel

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This door stop mounts on the refrigerator hinge to limit the door's swing and prevent overextension that can damage cabinets, hinges, or wiring. Replacing a worn stop restores smooth, controlled door opening and proper clearance.

• Controls the door's opening range by acting as a hinge stop
• Helps prevent the door from striking walls or adjacent cabinets
• Replaces cracked, missing, or deformed stops that allow overextension
• Common symptoms: door swings too wide, scraping/clicking at the hinge, or a visibly broken stop

• Unplug the refrigerator and, if applicable, shut off the water supply
• Remove the hinge cover; support the door to relieve weight on the hinge
• Lift the door off the hinge or remove the hinge pin as required; note the stop's orientation
• Install the new stop, reassemble, and verify door alignment and gasket seal

This defrost heater and bracket assembly melts frost from the evaporator during the automatic defrost cycle, restoring airflow and stable temperatures so your refrigerator and freezer cool as designed. What it does:

• Heats the evaporator coil at set intervals to clear frost and ice
• Keeps air passages open for consistent temperatures and efficient cooling
• Helps prevent excessive run times and ice buildup on the freezer back wall
• Failure signs can include heavy frost accumulation, weak/uneven cooling, or fan noise from ice

• One defrost heater pre-mounted to its bracket

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator behind the freezer's rear panel; safely defrost built-up ice before removal
• Note/photograph wire routing and connections; transfer like-for-like
• Avoid damaging evaporator fins and ensure the heater sits in the original position without touching plastic components

This right-hand bucket glide supports a refrigerator bin/drawer and forms the track it slides on. It restores smooth, level movement and proper alignment when the original glide is cracked, worn, or missing.

• Provides side support and a smooth sliding track for the bucket/drawer
• Helps keep the bin level and aligned so it opens and closes properly
• Replaces a cracked, warped, or broken right-hand glide
• Common symptoms: drawer sticks, binds, sags, or comes off its track

• Disconnect power and remove food from the affected drawer area
• Slide out the bucket and remove any shelf/frame as needed for access
• Remove mounting screws or tabs, note the glide's orientation, and transfer any hardware
• Position and secure the new right-hand glide; reinstall components and test drawer movement

This compressor-mounted start device combines the start relay and overload protector. It helps the compressor start reliably and safeguards it from overheating, supporting consistent refrigerator cooling performance. What it does:

• Provides the initial boost to start the compressor, then disengages once it's running
• Protects the compressor circuit by opening if current draw or temperature is too high
• Common symptoms of failure: refrigerator/freezer warm, compressor won't start, repeated clicking, brief humming then shutoff, intermittent cooling
• Restores normal compressor starts when the original device has failed

• One TSD-2 compressor start device assembly

• Disconnect power before service; work in a dry area and follow manufacturer safety guidance
• Access the compressor compartment and note wire positions/terminal layout before removal
• Pull off the old device; push the new device fully onto the compressor pins; transfer wires one at a time to matching terminals
• If your model uses a run capacitor or retaining clip, move and reconnect them exactly as originally configured

The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.  

Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Difficulty in opening or closing the door
• Visible cracks or breaks in the handle
• The handle detaching from the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.