Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement slideout shelf for your refrigerator freezer compartment. Adds storage or replaces a missing, cracked, or broken shelf. Easy install.
Just slid it in! Read more
Seals your refrigerator's fresh food door to prevent air leaks and maintain proper temperature. Replace if torn, cracked, or door won't stay closed. Verify fit.
Ordered replacement seals for both freezer and refrigerator sides. Followed directions that I had found on YouTube. The installation in a nut shell is warm the seals in a bathtub with very hot water for at least 2-3hrs then place the seals. Then warm the seals with a hair dryer as needed. After getting the seals out of the hot bath the installation took all of 20-25 minutes for both seals. Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
Replacement spring for refrigerator ice dispenser systems. Wraps around shifter lever to control crushed vs. whole ice selection. Replace if broken or stretched.
When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more
Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.
I replaced the lever asm. and spring Read more
Fix food freezing or warm spots in your fridge with a new air damper assembly. Controls airflow between compartments. Moderate DIY repair, 1-2 hours.
It started with clicking sounds for about 10 seconds at random times throughout the day. eventually the clicking sounds were gone and the temperature in the fresh food section was dropping below freezing. Turns out that one of the 3 damper doors was stuck open. My fridge has a damper door in the top left and 2 doors in the bottom left. One of the bottom doors was dedicated to the quick chill drawer which hadn't worked in some time. but since the quick chill door was stuck closed it did not... Read more
Water line fitting that connects the ice maker supply tube. Replace if cracked, leaking, or damaged to restore a secure seal and prevent water leaks.
Replaced water line from valve to ice maker Read more
Fix no water dispensing or leaking behind your refrigerator. This water inlet valve controls flow to the ice maker and dispenser. DIY repair in under an hour.
Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both Read more
Supports refrigerator drawers and ice trays, allowing smooth sliding access. Replace if bracket is cracked, broken, or missing due to wear or overloading.
The hinge broke on the ice dispenser funnel and housing. I took them off and replace them, putting the old switches and bulb in the new housing. It took some time to put the return spring back because it does not appear in the assembly diagram. Once working, it secures to the door with 4 screws, and worked as it should. The support slide inside the freezer is held with two 1/4 in screws that were taken off with a nut driver. the rear screw is hard to get at. The new bracket just screws on, and... Read more
Secures drawer rollers in your refrigerator's slide assembly. Replace if lost during maintenance, stripped, or missing to properly mount drawer wheels.
Used the schematic provided to select the parts needing replacement and placed the order. Parts arrived and swapping new for old was simple. For the most part it was a matter of taking out the old and putting in the new. There were a few screws with wheels to replace but that was easy as well. Before purchase I searched several different sites and found all the parts needed. I compared prices of each item as well as shipping cost. Prices for each item were nearly identical between sites... Read more
Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
Ice dispenser not working or jamming? The ice bucket helix moves ice cubes to the crusher. Moderately difficult repair requiring full disassembly.
Ice was not being dispensed when lever was pushed in either crushed or cubed mode I removed the ice bin. After searching the web for reasons for this I pulled the bin out and started looking at auger assembly. I noticed that the sections of the Helix blades were missing. Ordered the Helix here at AAP and received the part the next day. The whole process took about an hour and as others have noted, you have to disassemble the bin assembly to get the auger assembly out. I watched the video... Read more
Plastic shelf stop locks refrigerator shelves into liner slots. Replace if cracked, broken, missing, or lost during cleaning to secure shelves properly.
Watched short You Tube repair video. I saved at least on a $100 GE service call. The electronic ID assembly was priced much less than quote on GE.com! Read more
Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.
Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.
Ordered the parts from you. Watched a you tube video and then went for it. Repair took about 15 minutes. Now everything works perfectly. Read more
Ice cubes stuck together or ice maker not ejecting? The ice stripper removes ice from the mold during ejection. Easy snap-in repair with video guide.
Replaced the parts. Initially, in order to ensure the ice maker itself was still working, I did some repairs to test it. I repaired the cracked crusher cover with a plastic welder, I also repaired the glide bucket Lh with the plastic welder & some epoxy. I attached the broken ice stripper pieces with the plastic welder. If the ice maker made ice I knew it was safe to buy new parts. It made ice for two days only but after it dropped ice the first time I ordered the parts. Parts did not... Read more