Shv7pt53uc-04 Parts

I changed the control board (00498022) in the door of my Thermador dishwasher. Thermador, Bosch, and Siemens all use the same board for the indoor controls and display. This required a #15-star head driver to remove the screws. I used an impact wrench (set to a low torq setting) to speed things up. There are approximately 12 screws to remove. Two are long. The rest are short. Be careful to hold the door together as the last screws are removed. Everything comes apart easily and you do not... Read more

This turned out to be a major effort, requiring me to disconnect the dishwasher, pull it from the cabinetry and partially disassemble the dishwasher to replace the door closer pulley Read more

It finally gave E15 code, then after drying out the E15 code came back within 5 minutes of running. I dried out the base then I ran the dishwasher and observed water coming down the overflow chute after running only 5 minutes.There is a water inlet (clear water chamber on the side of the machine). It had some gunk inside that was stopping a black float shut-off from moving. I replaced the water inlet chamber. I also suspected the non return valve (also called a check valve). From the parts... Read more

• overflowing
• Noisy

Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more

The parts were to complete the install. Not a repair really. Although this was my first dishwasher install DIY. and thanks to the very fast and accurate parts delivery I was able to get everything done right the first time. Read more

I bought just the replacement lid based on other reviews. The door cost about a third of the whole soap dispenser module but took a chance it was just the lid. Although the part number is the same there was a new flange on the inside of the lid. Would have been nice if Bosch sent the redesigned part to owners. Either way replacement took 2 minutes and the problem is gone Read more

I contacted Appliance Parts Pros online and got troubleshooting advice. The advice I got was invaluable. I used the information I got from them and then ordered the parts they suggested and sure enough, my start problem was solved. The dishwasher is now working great! I was especially impressed with the friendly and professional ordering process from Stephanie C. that really helped with ordering the parts I needed. Read more

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more

Removed water out of basin, down to the last inch.. Watched water rise slowly, and felt temperature, warm. This told me it was supply water. Ordered replacement part, two days just as mentioned, Removed as per video. Also choose to replace the waste line check valve, to affordable not too. Working great, except the wood floor not so happy with. One thing at a time. Thanks Read more

Bought new wheel and the are easy to replace. Found why the brok and did a quick fix so it wont happen again. As the wheels age one will pull off then they all get weak and the rack will come off the track, To prevent this. you can put a plastic tie so the wheels cant fall off in the first place, The disign holds them in place with pressure from the plastic but the plastic ages and gets weak. A tie would have to actually break before the wheel can fall off. Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

I looked carefully at why this one row of tines might be wobbly and saw that the row of tines next to it was secured by these little plastic pieces that just seemed to snap on. So I Googled "parts for Bosch dishwashers" and Appliance Parts Pros popped up. I called the number on the website and the very nice person who worked on the phone asked for the serial number on the door of the dishwasher. Then I described what I needed. She identified it by my description. I ordered it, it arrived,... Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

Replaced dispenser Read more

"Watertap" E15 error code indicated leaking. Dried it all out to allow it to run again. Ran dishwasher with front and bottom panels off to get a visual on leak causing the styrofoam float to set off the code. Saw it was coming from the diverter area. Ordered this assembly -- which DOES include the seal ring, by the way -- pulled dishwasher all the way out to replace it, and VOILA. No more leaking or error code. (This took a few days to analyze and receive the part, so in the meantime we... Read more

Twist the old one out, insert tab, twist until other side snaps in. Easy as pie after watching the video! Read more