Sm2681220 Parts

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This rubber grommet cushions and secures a refrigerator fan motor, isolating vibration to help reduce noise and keep the fan properly aligned in its mount.

• Provides a snug, vibration-dampening seat for the fan motor shaft or mounting stud
• Helps prevent rattling, buzzing, or humming sounds from a loose fan mount
• Maintains proper fan alignment to avoid blade contact with shrouds or brackets
• Replaces aged, cracked, or compressed rubber that can lead to increased vibration

• Disconnect power before service; wear cut-resistant gloves
• Access the fan assembly (rear or evaporator section), support the motor, and remove the old grommet
• Press the new grommet fully into the bracket or housing; transfer any spacers as originally configured
• Reinstall the motor and verify the fan blade spins freely with no contact before restoring power

This replacement lamp restores illumination so you can clearly see inside your appliance. Replace a burned-out or damaged bulb to bring back visibility when the light switch is pressed or the door opens, depending on design.

• Provides interior illumination in the appliance compartment
• Activates with the door switch or dedicated light control, as designed
• Helps you see contents and monitor progress at a glance
• Common signs of failure: no light when activated, intermittent/flickering light, blackened glass, or a broken filament

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the bulb and surrounding area to cool before handling
• Handle the glass with clean gloves or a cloth to avoid oils that can shorten bulb life
• Use only the bulb type and wattage specified for your model; do not overtighten during installation

This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.

• Fastens panels, brackets, covers, and internal hardware to the cabinet or frame
• Helps prevent loosening, rattling, or misalignment during appliance operation
• Replace if the head is rounded, threads are stripped, or the screw is missing
• Useful after service when an original fastener is lost or damaged

• Disconnect power and shut off gas/water before starting
• Use the correct nut driver or socket for the hex head to avoid rounding
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

The Cabinet Roller is an OEM part for Whirlpool refrigerators. It facilitates the smooth movement and positioning of the refrigerator cabinet, making it easier to adjust or relocate the appliance as needed. This roller is designed to support the weight of the refrigerator while allowing for effortless mobility.

Causes of a bad Cabinet Roller can include wear and tear over time, exposure to heavy loads, or damage due to rough handling or impact. These factors can lead to the roller becoming ineffective or breaking altogether, resulting in difficulty moving the refrigerator.

Symptoms of a bad Cabinet Roller include:

• Difficulty moving or adjusting the refrigerator
• Unusual noises when attempting to move the appliance
• The refrigerator not sitting level or wobbling

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

This defrost heater warms the evaporator coil during the automatic defrost cycle to melt frost and clear airflow. Replacing a failed heater helps prevent ice buildup and restores more consistent cooling performance throughout the refrigerator. What it does

• Heats the evaporator during defrost cycles to melt accumulated frost
• Keeps airflow paths clear so temperatures stay stable
• Helps prevent frost-clogged coils that reduce cooling
• Common signs of failure: heavy frost on the back wall/evaporator cover, weak cooling, evaporator fan hitting ice, or ice returning soon after a manual defrost

• One defrost heater

• Disconnect power before servicing; wear cut-resistant gloves
• Access is behind the freezer's rear evaporator cover; remove shelves/bins and the panel
• Defrost heavy ice before removal to avoid damaging the coil or insulation
• Transfer any original mounting clips/insulators and route wires exactly like the original; avoid bending the heating element

The Switch is an OEM component specifically designed for Bosch microwaves. It controls critical heating elements and fan functions through the direct user interface. Seamless button response allows convenient operation.

Symptoms of a faulty switch involve non-responsiveness or inaccurate reaction to control presses. Opening from wear over extended usage risks compromised performance warranting replacement. 

Causes of a bad switch include normal degradation inhibiting smooth movements. Exposure to moisture-increasing interior corrosion necessitates a change to restore full functionality.

Symptoms of a bad switch include: 

• Microwave fails to start or prematurely stops cooking cycles  
• Inaccurate power levels result in uneven heating
• Inoperative special features like popcorn do not engage

This OEM Bosch part is also compatible with some Thermador, Blomberg, and Miele microwaves. Replace to maintain dependable command of essential microwave functions.
 

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This grommet is a small protective seal used where a hose, tube, wire, or component passes through or mounts to the appliance cabinet. It cushions the connection and helps prevent leaks, vibration, and wear for reliable operation.

• Provides a snug barrier between parts and metal openings to protect hoses, tubes, and wiring
• Helps seal against moisture to reduce seepage
• Dampens vibration and rattling noises
• Replace if cracked, hardened, missing, or no longer stays seated; symptoms may include drips at a pass-through, buzzing/rattling, or a loose fit

• Disconnect power; shut off water supply if applicable
• Access the grommet location and note orientation/routing
• Remove the old grommet and clean the opening
• Press the new grommet fully into place; reassemble and test for leaks/noise

Restore fast, even convection cooking with this rear convection heating element. It supplies a ring of heat around the fan at the back of the oven so temperatures rise and hold properly in convection bake and roast modes.

• Provides heat around the convection fan for uniform air circulation and even results
• Common symptoms: no heat or very slow preheat in convection modes
• Fan runs but temperature does not rise in convection
• Visible damage or a break in the element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove racks; access and remove the element's mounting screws from inside the oven (procedure varies by model).
• Pull the element forward carefully; label and transfer wires one at a time so they don't slip back into the cavity.
• Reuse existing hardware; ensure terminals are tight, reassemble, and test a convection cycle.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

The Oven Door Gasket Kit is an OEM replacement part for 27" Bosch wall ovens. It includes a gasket for insulating the oven cavity while in use and clips to secure it. Over time, heat and compression can break down gasket material allowing potential leaks of hot air from the oven during cooking or difficulty closing the door. Causes involve standard wear from repetitive door closing as well as exposure to high oven temperatures over many heating cycles.

Symptoms of failed gaskets include: 

• excessive heat escape from the door opening
• Door locking difficulties
• visible cracks or tears in the gasket materials 

Replacing the gasket allows for smooth door movement and an tight seal when closed. This Bosch part can also be used on Thermador and Gaggenau appliances.

This switch is an electrical component that opens or closes a circuit inside your appliance. Replacing a worn or failed switch restores proper signaling to the control so the selected function responds reliably when actuated.

• Opens/closes an electrical circuit to send an on/off signal to the appliance's control or motor
• Enables the appliance to start, stop, or register a user input as designed
• Common symptoms: no response when pressed/activated, intermittent operation, feature stuck on/off, or error codes referencing a switch
• Resolves issues caused by heat, wear, moisture, or mechanical fatigue of the original switch

• Disconnect power at the breaker before servicing; verify power is off
• Note wire locations and take a photo; move connectors over one at a time to the new switch
• Do not force or bend terminals; replace any loose or heat-damaged connectors
• Restore power and test the function before final reassembly