Wdf130pah82 Parts

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This overfill control float sits in the dishwasher tub and rises with the water level to signal the float switch to stop filling. Replacing a cracked or sticking float helps prevent leaks and recurring fill issues. What it does:

• Rises with the water level to actuate the float switch and stop the inlet valve
• Helps prevent overfilling and water leaking from the door
• A float stuck in the UP position can cause no fill or short fill
• A float stuck DOWN or damaged can allow overfilling

• 1 overfill control float

• Disconnect power and turn off water before servicing
• Remove the lower rack; lift out the old float from its guide and clear any debris in the well
• Insert the new float, ensuring it moves freely and reliably actuates the switch when raised

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This wheel mount assembly fits the dishwasher's upper rack track and provides the roller that lets the rack glide in and out. Replacing a worn or broken mount restores smooth movement and keeps the rack aligned on the rails. What it does:

• Supports and guides the upper rack along the side rails
• Replaces cracked, missing, or seized rollers that make the rack hard to slide
• Helps prevent the rack from popping off the track or sitting unevenly
• Can reduce scraping or squeaking noises when moving the rack

• One upper rack wheel mount assembly

• Disconnect power to the dishwasher before servicing
• Open the door and remove the upper rack by releasing the rail stops
• Depress the locking tab to remove the old wheel mount from the rail; align and snap the new assembly into place
• Reinstall the rack and rail stops; check for smooth rack travel

Color: blue. It measures about 2 inches in diameter.

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This mounting bracket holds and aligns the door interlock switch(es) so the control can accurately detect when the door is closed. Replacing a cracked or warped bracket restores reliable door recognition and consistent operation.

• Secures the door switch(es) in the correct position behind the front panel
• Maintains latch-to-switch alignment for proper door-closed detection
• Can address incorrect interior light behavior tied to door switch alignment

• Disconnect power before servicing
• Access the bracket by removing the necessary front/console panels
• Transfer existing switches and wiring to the new bracket; note wire positions
• Align and tighten fasteners; confirm switches click and door closes properly before reassembly

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Bushing, Door spring

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

This surface burner gas manifold assembly routes gas from the supply to each burner on your range or cooktop. Replacing a worn or damaged manifold restores safe, consistent gas flow and reliable burner operation.

• Distributes gas evenly to the surface burners via the manifold rail
• Serves as the mounting/connection point for the burner control valve bodies
• Common symptoms include burners not lighting, low or uneven flames, or a gas odor near the control area
• Restores proper gas delivery after damage, corrosion, or impact to the original manifold

• Disconnect electrical power and shut off the gas supply before servicing.
• Take clear photos and label all connections to ensure correct reassembly.
• Use only gas-rated thread sealant where specified by the manufacturer and tighten fittings securely.
• After installation, restore gas and check all joints with a leak-detection solution; verify every burner ignites and flames are stable.