Wed6000vw0 Parts

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This broken belt switch is a dryer safety switch that senses drive belt tension and opens the motor circuit if the belt breaks or slips off. Replacing a failed switch can resolve a no-start or no-tumble condition. What it does:

• Monitors drive belt tension via the idler assembly
• Interrupts power to the motor when the belt is broken or not tensioned
• Helps prevent heating without airflow when the belt has failed
• Symptoms can include: dryer won't start, drum won't turn, or the dryer stops as soon as the Start button is released

• 1 switch

• Disconnect power; for gas models, shut off the gas supply
• Access the switch near the idler pulley by removing the lower/front panel per your model
• Transfer wires from the old switch to the new one; mount securely with the actuator aligned to the idler arm
• Run a brief test cycle

Specs: 10-16 x 1/2 inch.

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles

Side and bottom exhaust kit.

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

STACK KIT FOR LONG VENT DRYER

This drying rack sits inside the dryer drum to hold items stationary for tumble-free drying. It's ideal for shoes, sweaters, and other delicate pieces that need air circulation without bouncing or spinning, helping prevent damage and excess noise. What it does:

• Provides a stable surface for no-tumble drying inside the drum
• Helps prevent scuffs, stretching, and wear on delicate items and footwear
• Replaces a missing, cracked, or warped rack
• Common signs you need a new rack: won't seat securely, bent or broken frame, or persistent rattling when in use

• 1 drying rack

• Unplug the dryer and allow the drum to cool before placing the rack
• Open the door and position the rack per your owner's manual so it sits level and secure
• Load items evenly; ensure nothing contacts the rotating drum
• Use only the rack-dry/low-heat/air cycles recommended for your model; remove the rack before normal tumbling cycles

This thermal cut-off (TML) is a temperature safety device that opens the circuit if overheating is detected, protecting components from heat damage. Replace a failed or tripped cut-off to restore safe, reliable operation.

• Monitors temperature at its mounting point and interrupts power at a preset limit
• Helps prevent overheating damage to components and wiring
• Typical symptoms include no power, shutting off during use, or no heat—depending on where it's installed
• Can be tested with a multimeter; an open (no continuity) reading indicates replacement is needed

• Disconnect power before servicing; some appliances (e.g., microwaves) can store dangerous high voltage—use proper discharge procedures
• Replace with the same type/rating and mount in the same location/orientation as the original
• Ensure solid contact with the sensing surface and clear airflow/venting to prevent repeat overheating
• Do not bypass thermal safety devices; verify proper operation after installation

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

The Dryer Door Hinge Assembly is an OEM part for Whirlpool electric and gas dryers. As a critical component, this assembly supports the dryer door and allows for smooth opening and closing. 

Causes of failure include frequent use, which causes hinge components like bushings and bearings to wear out more quickly over time. Housing cracks or mechanical loosening from repeated operation are other issues.

Symptoms of a faulty door hinge assembly include: 

• Door that won't stay closed securely or slams shut on its own   
• Difficulty smoothly opening and closing the door
• Excessive gaps around the edges that allow lint to escape

This genuine Whirlpool replacement fits Maytag, Amana, Jenn-Air, Magic Chef, and select Kenmore dryers.

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

This high-limit thermostat is a temperature safety switch for the heating circuit. It opens the circuit if temperatures climb too high, helping protect the appliance and restore safe, reliable heating performance.

• Monitors temperature and interrupts power to the heater when a limit is exceeded
• Helps prevent overheating that can damage components or trip other safeties
• If failed open: heater won't energize; cycles may run long or never reach target temperature
• If stuck closed: unit may overheat or shut down as other safety devices trip

• Disconnect power at the breaker before servicing; allow the appliance to cool completely
• Access the thermostat at the heater/temperature control area as designed for your model
• Note wire positions and transfer one at a time; ensure tight, secure connections
• After replacement, inspect the heater and controls for issues that could cause overheating

This is the stirrer motor assembly that drives the metal stirrer in the microwave's waveguide. A working stirrer helps distribute microwave energy more evenly, reducing hot and cold spots for consistent heating.

• Rotates the mode stirrer to spread RF energy inside the cavity
• Symptoms of a failing motor can include uneven heating, cold spots, buzzing or grinding from the waveguide area, or the stirrer not turning
• May restore even cooking performance when the original motor is worn or seized

• Unplug the appliance before servicing; high-voltage components in microwaves can retain a dangerous charge
• Remove the grill/cover and access panel to reach the stirrer motor location
• Transfer any mounting hardware from the original part if not supplied
• Ensure the stirrer blade or coupler is correctly seated and turns freely before reassembly

This in the male piece on the front panel. For the female piece on the door order WPW10111905.