Wfl 2060/Wfr Parts

This valve magnet is the solenoid actuator used to open and close a dishwasher water/control valve, restoring proper water flow for filling and cycle operation. It replaces a failed or weak magnet to help the valve respond correctly. What it does:

• Converts electrical signal into linear motion to operate the dishwasher valve
• Restores valve opening and closing when a worn or stuck magnet causes fill or circulation issues
• Commonly used when dishwasher won't fill, stops mid-cycle, or shows related valve/fill errors
• Works with the valve body; does not include seals or the full valve assembly

• Disconnect power and shut off the water supply before beginning service
• Replace with the matching OEM magnet and ensure proper seating on the valve body
• Keep terminals dry and secure electrical connections; inspect gaskets and valve body for damage

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This door-mounted dispenser stores and releases detergent and rinse aid at the correct times during the cycle, helping restore consistent cleaning and drying results. Replace a worn or damaged unit to fix soap door and rinse aid issues.

• Holds detergent for the main wash and opens the cup during the programmed step
• Meters rinse aid into the final rinse to reduce spotting and improve drying
• Helps resolve symptoms like detergent left in the cup, soap door won't latch/open, leaking rinse aid, or poor cleaning performance
• Direct replacement for the original door dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire harness
• Release the retaining tabs/screws, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser flush, tighten mounting screws evenly, reconnect wiring, and run a test cycle to check for leaks and proper operation

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Contains two, six foot long braided hoses with 90 degree ends.

This is a valve magnet intended for use in washing machines. The valve magnet's purpose is to allow water to flow into the appliance during the different washing and rinsing cycles.Signs that indicate the valve magnet is malfunctioning or damaged include the washing machine shutting off before the cycle is over, water overfilling the machine, or water not shutting off at all. The replacement of the part is a simple process. Disconnect the appliance from its power source first. The water connections should also be shut off and removed from the washing machine. Wear gloves for safety. Ensure all connections are secure before reconnecting the device to the electrical outlet.This valve magnet is a genuine OEM replacement part. It is sourced from the manufacturer. The valve magnet is sold as an individual unit. The part is made of durable, high-quality materials. It can be installed in several models of washing machines. It is compatible with devices produced by Bosch, Thermador, and Gaggenau.

This replacement foot supports and levels your appliance so it sits steady and operates smoothly. Replace a worn or missing foot to restore proper height, reduce wobble, and help protect surrounding surfaces.

• Supports the base/frame to maintain proper height and alignment
• Provides leveling adjustment so the unit remains stable
• Helps reduce rocking, vibration, and rattling during operation
• Replace if the original foot is cracked, stripped, missing, or won't adjust

• Disconnect power; shut off water or gas supplies if applicable
• Carefully tilt or raise the unit to access the foot location
• Remove the damaged foot and install the new one per design
• Level the appliance front-to-back and side-to-side; verify stability before use

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

The Drive Belt is an OEM part for Bosch washing machines. It is responsible for transferring power from the wash motor to the wash drum, providing rotational motion needed for thorough cleaning cycles.

Causes of a bad drive belt can include wear and tear over thousands of wash cycles, cracks developing from repeated flexing and stretching. Accumulation of lint or other debris wrapped around the belt could also impact performance over time.

Symptoms of a bad drive belt include:

• Abnormal noises or vibrations coming from the washer during operation
• Reduced or inefficient spinning of the wash drum
• Clothing not receiving full agitation or movement for effective cleaning

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This replacement cam is a small drive component that converts rotational input into controlled movement inside the appliance mechanism. It helps the linked assembly engage in the correct sequence for smooth, reliable operation.

• Guides and times movement of the connected parts for proper engagement
• Restores smooth operation when the original cam is worn, cracked, or stripped
• Helps address binding, clicking/popping noises, intermittent operation, or parts not actuating
• Helps maintain alignment to reduce wear on mating components

• Disconnect power to the appliance; also shut off water supply
• Access the mechanism per your model's service information; note the cam's orientation before removal
• Transfer any springs, clips, or spacers from the original cam as needed
• Inspect mating followers/pivots for wear; test movement by hand before reassembly

This replacement lever is a small mechanical link that engages or releases its mating mechanism inside the appliance. Replacing a worn or broken lever restores crisp actuation and reliable operation of the related control or latch. What it does:

• Transfers motion from a button, handle, or cam to the connected mechanism (such as a latch, switch, or dispenser component)
• Ensures the mechanism moves fully and smoothly
• Wear or breakage can cause a loose feel, incomplete travel, or no response when pressing/pulling the control
• Visible cracks, missing tabs, binding, or intermittent operation are common signs it needs replacement

• 1 lever

• Disconnect power before servicing; also turn off water supply
• Access the assembly for your model per the service/parts diagram
• Note orientation of any springs or clips connected to the original lever; transfer them if present
• Reinstall with existing fasteners and test operation before reassembly