Whirlpool Gu2275xtvy1 Parts

This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.

• Screens large food particles and debris from the pump/chopper inlet
• Helps maintain proper water circulation and consistent cleaning performance
• Reduces risk of pump damage or noisy operation from debris
• Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack and spray arm; access the sump/accumulator area per your model
• Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
• Reassemble and ensure the screen sits flat with no gaps

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Color: gray. Measures about 3 inches wide by 1-1/2 inches high.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Bushing, Door spring

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

Color: light gray. Measures about 3 inches high by 6 inches deep.

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

Located between the console and door