Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix screeching or clanking noises in your dryer. This push clip secures the drum support roller assembly. Moderate DIY repair, requires drum removal.
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more
If your dryer door won't latch or the dryer won't start when you close the door, this top lock secures the cabinet during cycles. Easy 30-minute fix.
Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer. Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours. Read more
Dryer won't heat or overheats? The high limit thermostat monitors drum temperature. Moderate DIY repair with heater housing access required.
I purchased a new heating element. Very easy to fix in about twenty minutes Read more
Secures the handle end cap to the center of your refrigerator door. Replace if missing, stripped, or lost during handle repairs. 8-18 x 1/2 inch size.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more
The heater box houses your dryer's heating element and screen. Replace this component when rusted, corroded, or the screen is damaged causing snags or stains.
Replaced the heater tube. Had to open the back up, removed the heating element and then replaced the heater tube. Then I put it all together again and everything is fine now. Read more
Prevents water and air leaks at the dryer front panel. Replace if worn, cracked, or causing moisture issues. Verify fit with your model number.
First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more
Metal washer for dryer drum roller support shaft. Replace when you hear tapping, thumping, or squealing noises during operation. Confirm fit with model.
Replaced the roller, shaft, rings and washer. After removing the back, reverse threading the nut off, discarding the old hardware and installing the new hardware back in business in about 20 minutes. Read more
Replace your dryer door seal to prevent heat and moisture from escaping around the door edge. Installs by pulling off the old seal and pressing the new one into the door slots. Verify fit by model number.
Put new seal on. Read more
Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more
Dryer won't start when you press the button? The start switch sends the signal to begin the cycle. Simple 5-10 minute fix with basic tools.
Two screws remove the top. Unplug the wires to the old relay, give it a quarter turn and it's out. A five minute procedure. What took five hours was replacing the dryer duct work that I discovered was mostly crushed on its way from the laundry room, through a couple of walls to the exterior. Read more
Dryer takes multiple cycles or over-dries clothes? A faulty moisture sensor prevents proper drying time adjustment. DIY fix in 30-45 minutes.
Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more
Secures the dryer's lower access panel in place. Replace this spring retainer clip if it's bent, broken, or missing to properly hold the panel closed.
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now. Read more
Secures the idler pulley to maintain proper drum belt tension in your dryer. Replace if worn, loose, or causing squealing noises. Confirm fit with your model.
Using You Tube How-To Videos. Replaced the drum drive belt and tensioner pulley/arm (including) the spring. Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
And after replacing the thermal fuse The dryer turned on. Read more