Wlsr4460g0ww Parts

This lid assembly kit replaces a damaged or broken top-load washer lid to restore a secure, flush cover and proper lid operation. Designed as a direct replacement to help the washer close and latch correctly. What it does:

• Replaces a cracked, warped or broken washer lid that no longer closes or stays shut
• Restores a proper fit and alignment so the lid can latch and allow normal cycle operation
• Prevents debris from entering the wash tub through a damaged opening
• Helps reduce noise and vibration caused by a loose or ill-fitting lid

• Disconnect power to the washer before starting any work
• Follow the manufacturer's service instructions and use appropriate tools for removal and installation
• Check lid alignment and latch engagement during installation to ensure proper operation
• If you find additional damaged parts (hinge, latch, strike), replace those components per OEM recommendations

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Agitator Assembly is an OEM part for GE washing machines. This part moves clothes through the water and detergent during the wash cycle. This part ensures thorough cleaning by creating the necessary motion to distribute and cleanse laundry evenly. 

Causes of a bad Agitator Assembly can range from wear and tear over extended use, to damage from overloading the washing machine, or even issues with the drive mechanism that powers the agitator's motion.

Symptoms of a bad Agitator Assembly include:

• Clothes coming out of the wash still dirty or not as clean as expected
• The washing machine making unusual noises during the wash cycle
• The agitator not moving during the cycle or moving erratically

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Timer is an OEM replacement part for GE washers. The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

Causes may involve minor power surges exposing delicate components to uncontrolled fluctuations overtime. General wear from years of activating various thermal, agitation and spin functions can degrade sensitive electronics as well.

Symptoms of a bad timer include:

• Erratic or inaccurate countdown between cycles
• Failure to switch automatically between rinse and spin
• Locked buttons or controls suggesting circuit board issues
• Inability to modify or set desired cycles and options

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore model washing machines.

The Washer Top is an OEM part for GE washers. It is the upper panel that covers the internal components of the washing machine and provides a flat surface for loading and unloading laundry.

Causes of a bad Washer Top can include physical impact, warping due to prolonged exposure to heat or moisture, or general wear and tear over time.

Symptoms of a bad Washer Top include:

• Visible cracks, dents, or damage to the top panel
• Difficulty opening or closing the lid due to misalignment or warping
• Water leaks around the top area during wash cycles
• Excessive noise or vibration caused by a loose or damaged top

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water level pressure switch monitors the tub's fill level and tells the washer when to stop filling and move to the next step. Replace it to restore accurate water levels and dependable cycle progress.

• Monitors air pressure from the tub to determine the selected water level
• Signals the control to open/close the inlet valves for proper fill
• Allows agitation and spin only after the correct level is reached
• Typical symptoms: overfilling or continuous filling, underfilling/low water level, cycle won't start or advance to wash/spin

What's included: 1 pressure switch Install notes:

• Unplug the washer and turn off the water supply before servicing
• Access the control console; note wire positions or take a photo and transfer connectors one at a time
• Move the pressure hose to the new switch; ensure the hose is clear, undamaged, and fully seated
• Secure the switch, reassemble, and run a fill test to confirm proper shutoff

The Drain Hose is an OEM part for GE washing machines. It is specifically designed to channel used water out of the washer and into the household drainage system. 

Causes of a bad drain hose can include physical damage from movement or installation, clogging from lint and debris, or degradation of the hose material over time, leading to leaks and inefficiency.

Symptoms of a bad Drain Hose include:

• Water leaking from the back or underside of the washing machine
• Pools of water around the area where the washing machine is installed
• Signs of wear or damage to the hose, such as cracks, holes, or bulging

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This electronic control board manages key washer operations so cycles start, run, and finish as designed. Replacing a faulty board can restore proper agitation and spin performance and resolve intermittent or no-run behavior. What it does:

• Regulates drive motor operation for agitation and spin
• Processes inputs from sensors/switches to carry out selected cycles
• Coordinates start/stop, speed, and direction commands to the motor
• Common symptoms of failure: won't agitate or spin, intermittent stopping, motor won't run, visible damage on the board, or related error codes

What's included:

• 1 electronic control board

Install notes:

• Disconnect power before servicing; observe ESD precautions and handle the board by the edges
• Note/photograph wiring; transfer any jumpers, brackets, or mounting hardware from the old board if applicable
• Ensure all connectors are fully seated and harnesses are undamaged before powering up
• Run diagnostics or recalibration if required by the model's service/tech sheet after installation

This genuine OEM part is a drive motor for washers. The drive motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the drive motor needs to be replaced. Luckily, replacing this part is a relatively simple repair.To replace the drive motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting screws holding it to the washer. Proceed to pull the old motor out of its place and install the new motor by threading the screws that secure it. This replacement part is sold individually and is compatible with GE, RCA, and Hotpoint brand washers.