Wm3575cw Dlgx3571w Parts

• Will not agitate

Swapped bad part for new part. Read more

I opted to save myself about $600 by repairing my 8 year old LG washing machine rather than buying a new one. After watching some videos I determined what I needed upon taking my washing machine apart. I ended up replacing the tub (includes spider and shaft), since I could not get the spider part removed from the original tub, as well as the motor bolt (which had broken when I removed it from the original tub's shaft). The spider was cracked and the shaft was wobbling which caused it to... Read more

This was Kenmore front load washer made by LG. Model 796.41302610 First, AppliancePartsPros.com has been great. This is my fourth time using them. Staff, DIY comments, and videos are all very helpful. Always ended up with the right part and received next day. The machine made an odd noise on start-up. I ran diagnostics. Had a problem finding how to do diagnostics since the instructions in the manual were wrong. Found the correct process on YouTube. Needed to hold the spin and soil buttons... Read more

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more

Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more

I removed the barrel from the inside of the washer, and removed the tub after that I punched out the bearings and replaced them with the ones that were sent which by the way I received within a couple of days. I ordered the inner bearing outer bearing and the seal. Read more

1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more

Replaced seal and back bearing Read more

I also noticed one of the two water recirculation outlets near the front door was no longer spraying water. When I took it all apart, I found that these two tub water recirculation outlets are both connected to the pump.. one was clogged. The impeller on the drain pump was no longer spinning with the motor.. looks like it was worn on the inside.. when I took the pump apart it was full of scale. I could have just ordered the motor...but I figured I would replace the entire assembly as I also... Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Took top off and did a line at a time Read more

The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more

I suspected the tub gears where ready to break so I dismantled my LG WM2032HW front load washer. I found the spyder gear corroded and broken. I also found that the stainless steel drum abraded the front tub cover so bad, it was cracked. My washer is an early model and always had standing water in the door seal after a wash. What I learned is LG stopped making the orginal front tub cover and replaced it with one that had a drain hole at the bottom front edge. I also learned that this new... Read more

My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more

Technician wanted $700. I was able to fix it myself for around $300 in about a half hour with the great and helpful customer service of appliancepartspros.com. Parts arrived on time. Nice to know there is a company that really cares and they know there stuff. Read more

Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more