Need Help?
Call or text
Plastic support bracket that secures shelves inside your refrigerator door. Replace if cracked, broken, or missing to restore stable storage for bottles.
Easy to replace with the shield and paddle assembly. Steps are: 1. use a flat head screwdriver to push the tabs at the base of the control panel. remove the wire connectors by gently prying them straight off. 2. remove the 4 phillips screws holding in the old assembly. 3. Install the new assembly by carefully putting the paddle behind the water pipe that sticks out. You may have to push the paddle one way to get it around the pipe and then back into place. 4. reinstall the screws. 5. reconnect... Read more
Replacement door shelf for refrigerators. Installs on the door to organize condiments, jars, and bottles. Replace if cracked, broken, or missing.
Yes exact fit Read more
Fix F30 error code or clicking noise from soap dispenser area with this actuator. Controls detergent release timing. Easy 20-minute DIY repair with video.
After watching the YouTube video provided by Appliancepartspros and checking various forums I determined the dispenser motor had gone out. Turns out, it was a two part problem. The connectors to the motor, and the motor had corroded. Cleaned them both with vinegar. The old motor did a load before I started having problems with the CCU. I didn't learn about the CCU needing a reset under the quick diagnostics until after replacing the motor and the new part doing the same thing. Both the new... Read more
Repair kit for refrigerator drawer slide mechanisms. Includes gears and rod to replace stripped, broken, or missing components in pull-out drawer rails.
Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more
Replace your broken or cracked refrigerator snack pan rail. This slide rail supports and guides the snack drawer for smooth access. Easy one-screw install.
My husband unscrewed the broken railing and slipped in the new railing and screwed it in place. The new snack drawer was then sled in. The screw they provided was tight but after twisting it a few times went into the railing hole fine. Read more
Clear plastic lid cover for refrigerator pantry drawer. Replaces cracked, broken, or missing pantry lid. Snaps into place over drawer compartment.
Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more
Replacement door bin for refrigerator storage. Installs in the door to hold bottles, condiments, and containers. Order if your bin is cracked or broken.
So easy. Old ones just lift out and new ones just slide in. Such an easy fix! Read more
Replaces the metal panel at the base of your oven interior. Installs on the oven floor. Needed when original is warped, rusted, or damaged by foil.
Replaced bottom panel Read more
Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.
I replaced the dispenser assembly and since this was being replaced, I installed a new drawer and detergent box assembly. Read more
Left-side end cap for refrigerator pantry or deli drawer. Replaces broken or cracked caps with damaged support tabs that secure the drawer cover.
Right-side gasket replacement was straightforward. Left side required removal of mullion, which stumped me. I contacted Appliance Parts Pros who gave me the necessary instructions: Remove the center screw and lift up the mullion. Simple enough, once I knew how to do it. Read more
Replacement crisper pan for bottom-mount refrigerators. Stores fruits and vegetables in the fresh food compartment. Replace if cracked, broken, or missing.
The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more
Refrigerator shelf frame that supports glass or wire shelves inside the fridge. Replace if cracked, broken, or warped to restore proper shelf support.
No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more
Upper freezer door bin for side-by-side refrigerators. Installs above ice chute. Replace if cracked, broken, or missing. Measures 13"L x 5.5"W.
Ordered part from appliancepartspros.com and got them within 2 days.that was great,refrigerator is like new again,am I am pleased with service and there swift delivery. If I need any thing else,there is only one place I will get them.from. Thanks! Read more
Replacement glass shelf for refrigerator interior storage. Installs in shelf frame to hold food items. Order if original is cracked, shattered, or broken.
I took apart the old bucket with a screwdriver and put the new one with no problems. Read more
Replacement drawer track guide for refrigerator shelves. Installs on shelf assembly to support sliding drawers. Order when track is cracked or broken.
After sliding out the old shelf I removed the middle track from the old shelf & installed it with the new left side track on the new shelf. They basically click in & out. Slid the new shelf assembly in & put meat drawer in place. Read more
Adjusts the upper rack height in your dishwasher. Replace if cracked, broken, or missing. Mounts on the side of the upper rack to control positioning.
Took out 3 torx screws on each side, much of the insides fell out at this point. At this point I had the new part and what was left of the old part and the adjust lever. Screwed them back together and that was that. The new support piece was not needed. Read more