Water Valve Parts

This surface burner valve controls gas flow to a cooktop or range burner for smooth ignition and precise flame adjustment. Replacing a worn valve restores reliable lighting and consistent simmer-to-high control at the knob. What it does:

• Regulates and meters gas flow to a surface burner from Off through all heat settings
• Wear or blockage can cause no ignition, hard-to-turn knob, or poor/unstable flame
• Helps correct burners that won't adjust properly or won't stay lit
• Ensures safer, consistent burner performance when operating correctly

• 1 surface burner valve

• Disconnect power and shut off gas supply before servicing; allow appliance to cool
• Work in a well-ventilated area and follow local codes
• Note knob orientation; transfer any orifice fittings or mounting hardware from the old valve
• After installation, check all connections for leaks using a non-corrosive leak-detection solution

This dishwasher float rises with the water level to engage the float switch. It regulates filling and helps prevent overflows, protecting your kitchen from leaks and keeping wash cycles running properly. What it does:

• Rises with the tub's water level and actuates the float switch
• Signals the inlet valve to stop water flow at the correct level
• A stuck, worn, or broken float may cause overfilling or no-fill conditions
• Symptoms can include leaking from overfill or no water entering during fill

• 1 float

• Disconnect power and turn off the water supply before servicing
• Open the door; remove the lower rack for access
• Lift off any float cap/retainer, pull the old float straight up, and seat the new float
• Ensure the float moves freely; restore power/water and run a brief fill test

This dishwasher water inlet valve controls the flow of water into the tub during the fill cycle. Replacing a sticking or leaking valve restores proper filling performance and helps prevent unwanted water or leaks.

• Opens and closes to allow the correct amount of water into the dishwasher
• Works with the control/float system to stop water flow at the right time
• Typical symptoms: won't fill or fills slowly; hums but no water; leaks at the valve or hose connections; water seeping into the tub when the unit is off

• Disconnect power and shut off the water supply before servicing
• Access the valve behind the lower kick panel; label/photograph wire positions and place a towel to catch residual water
• Install in the same orientation; secure the outlet hose with the included clamp and reconnect the inlet line and wiring
• Restore water and power, run a short fill test, and check all connections for leaks

Does not include instructions.The only literature inserted is a notification stating that these valves no longer come with the harness

Note: Due to design change, new part may look different but is still a functional replacement.

Water inlet valve controls water flow to the refrigerator's dispenser and ice maker. Replacing a failed valve restores normal water delivery and can resolve symptoms like no water, weak flow, or continuous running/filling. What it does:

• Opens to allow water into the ice maker and dispenser when requested.
• Closes to stop water flow and prevent overfilling.
• Common symptoms: no water from dispenser, slow/weak water flow, or the ice maker not filling.
• Also used when leaks or intermittent water flow are traced to the inlet area.

• Disconnect power and shut off the home water supply before servicing.
• Relieve line pressure by dispensing water or gently loosening a downstream connection.
• Inspect fittings and seals; tighten connections snugly but avoid overtightening.
• After installation, turn on water and power, check for leaks, and verify dispenser/ice maker operation.

New seals come with this valve.

Valve flapper for the washer's dual-pump drain assembly that directs water between pumps for proper draining. Replacing a worn or torn flapper helps restore drain operation and reduce leaks or poor drain performance. What it does:

• Directs water flow between the washer's dual drain pumps to ensure proper draining.
• Commonly linked to symptoms such as slow or incomplete draining, water remaining in the tub, or intermittent leaks.
• Replaces a cracked, torn, or hardened flapper that no longer seals or diverts flow correctly.

• Disconnect power and turn off water supply before beginning any repair.
• Access typically requires removing the washer's front or rear access panel and the drain pump assembly—use basic hand tools.
• Test drain function with a short cycle and check for leaks.

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Control the water going into your washer with this triple water inlet valve. Three solenoids open and close to deliver water to the correct fill circuits or dispensers so cycles start and dispensing happens where it should.

• Regulates water flow into the washer when energized by the control
• Routes water to the correct fill path or dispenser compartment via three independently controlled outlets
• Common symptoms: no fill or slow fill, only certain cycles/dispensers receive water, water drips into the tub when off, or leaks at the valve/hose connections

• Unplug the washer and shut off the water supply before servicing
• Place towels, disconnect inlet hoses, and label/photograph wire connectors and outlet hoses for correct reassembly
• Transfer any mounting hardware from the old valve if required; ensure hoses/orientation match their original positions
• Restore water and power, then check all connections for leaks and run a test fill

Replacement water inlet valve that controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery and helping stop leaks or no-water conditions when the factory valve fails. What it does:

• Opens and closes the water supply to the ice maker and dispenser when signaled by the refrigerator's control board.
• Commonly linked to symptoms such as no water from the dispenser, slow fill, or ice maker not filling.
• Can fail by leaking, sticking closed, or not responding to electrical signals.
• Works with the refrigerator's tubing and fittings to route incoming household water to internal components.

• Disconnect power and shut off the refrigerator water supply before beginning work.
• Relieve water pressure and have towels handy to catch residual water when removing tubing.
• Verify electrical connector and inlet/outlet fittings match the appliance; replace any damaged tubing or seals.

This smart electronic valve regulates on/off flow inside the appliance under command of the control system, helping the unit fill, dispense, or operate as designed. A precise, electronically driven valve is critical for consistent performance.

• Opens and closes when energized to start or stop flow to the connected system
• Coordinates with the control board for timed, accurate operation
• Helps prevent overfill or underfill conditions
• Common symptoms of a failing valve: no fill/flow, slow or intermittent flow, continuous flow when off, leaks from the valve body, or related fill/flow error codes

• Disconnect power and shut off the appliance's supply line upstream before servicing
• Keep towels or a container handy to catch residual fluid when lines are disconnected
• Transfer connectors and any reusable brackets from the old valve to the new one, matching orientation
• After installation, restore supply and power, then check all connections for leaks and proper operation

This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.

• Controls incoming water to achieve correct fill levels and temperature mix
• Addresses no fill, slow/partial fill, or water seeping into the tub when off
• Replaces valves that are electrically failed or mechanically clogged/sticking

• Disconnect power and shut off both water supplies before servicing
• Have towels ready; relieve hose pressure and note wire/hose locations (take a photo)
• Transfer any mounting parts from the original valve if required; avoid overtightening plastic fittings
• Restore water slowly, check for leaks, and run a test fill

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:

• Monitors tub water level and actuates the float switch to shut off the inlet valve
• Helps prevent overfilling and water leaking from the door
• Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level

• Float and retainer

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift out the old float
• Access beneath the tub may be required to release/install the retainer
• Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks

If machine has 2 coil valve, order part #WP22003834.