Ptc Parts

This push button switch mounts in the appliance's control panel and sends an electrical signal to the control when pressed. Replace a worn or sticking switch to restore dependable button response and function activation. What it does:

• Panel-mounted switch that closes its contacts when pressed to signal the control
• Restores reliable front-panel input for starting or selecting a function
• Helps address no response or intermittent response when the button is pressed
• Replaces switches with loose action, sticking, or heat-discolored/burned terminals

• 1 push button switch

• Disconnect power before servicing to avoid electrical shock
• Access the console/control panel to reach the switch
• Note wire positions (take a photo) and transfer connectors one at a time; ensure firm, fully seated terminals
• Secure the switch in the panel (nut/clip as applicable), verify button action, then reassemble and test

The Pressure Switch is an OEM part for Whirlpool washing machines. This switch monitors the water level inside the washer tub and signals the control board to stop filling and start the wash cycle once the desired water level is reached. 

Causes of a bad pressure switch can include electrical malfunctions, wear and tear from regular use, or blockages in the pressure hose that connects to the switch.

Symptoms of a bad pressure switch include:

• The washing machine overfilling or underfilling with water
• The washer not advancing to the next cycle
• Error codes related to water level sensing
• Inconsistent water levels during different cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water level pressure switch senses the tub's water level and relays it to the washer's control. Replacing a failed switch restores proper filling and cycle progression while helping prevent overfilling, underfilling, or long-fill interruptions.

• Monitors air pressure from the tub to determine water level
• Signals the control/timer to stop filling and start the wash or spin
• Helps prevent overfill conditions and incorrect water levels
• Helps resolve symptoms like no fill/long fill, continuous filling, or cycles that won't advance

• Disconnect power and shut off water supply before servicing
• Access the control/console area; note wire and hose positions for reassembly
• Transfer the pressure hose and electrical connector to the new switch; ensure the hose is clear, undamaged, and fully seated
• After installation, run a diagnostic or calibration procedure for your model

The Lid Switch Kit is an OEM part for GE washing machines. This part detects whether the washer lid is closed, and allows the machine to operate only when the lid is properly shut. This safety feature prevents the washer from running when the lid is open, ensuring safe and efficient operation. For the magnet assembly order WH12X10276.

Causes of a bad lid switch can include wear and tear from regular use, electrical issues, or physical damage from rough handling.  

Symptoms of a bad lid switch include:

• The washing machine not starting or stopping mid-cycle
• The washer not agitating or spinning
• The machine running only when the lid is manually pressed down
• Error codes related to the lid switch

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This compressor start device briefly energizes the compressor's start winding to get it running, then disengages automatically. Replacing a weak or open PTC can restore cooling and stop the repeating hum-click from the compressor area.

• Provides the initial boost for the compressor to start, then opens as the PTC warms
• Helps the compressor start reliably on each cooling cycle
• Works with the compressor's overload protector to safeguard the motor circuit
• Common symptoms of failure: not cooling, compressor won't start, rapid clicking or hum-click every few minutes, intermittent cooling after power cycling

• Disconnect power and pull the unit forward to access the compressor compartment
• Remove the start-device cover; note wire positions
• Pull the old start device straight off the compressor terminals; avoid bending the pins
• Align the new device with the C–S–R terminals in the same orientation, push on fully, reconnect wires, reinstall cover, and restore power
• Inspect the mating overload protector and terminal connectors for heat damage before reassembly

The Push Button Switch is an OEM part for Whirlpool washing machines. This part activates various functions and cycles on the control panel of the washer. The switch is designed to ensure responsive and reliable operation when selecting wash settings.

Causes of a bad push button switch can include wear and tear from frequent use, exposure to moisture, or physical damage from impacts.

Symptoms of a bad push button switch include:

• Unresponsive buttons on the control panel
• Inability to start or change wash cycles
• Intermittent operation of washer functions
• Error codes related to control panel issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Door Switch is an OEM part for Frigidaire clothes dryers. It is an electronic component located on the door frame that detects when the dryer door is latched closed. The switch communicates this information to the control board, allowing the dryer to operate properly by preventing operation if the door is open.

Causes of a bad door switch can include normal wear and tear from opening and closing the dryer door over time. Physical damage from accidental impacts or overtightening of door mounting hardware may also cause switch failure.

Symptoms of a bad dryer door switch include:

• The dryer starting a cycle even when the door is open
• Error codes or failure to start/run if the door switch does not detect proper closure
• Other control issues related to incorrectly sensing door position

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This PTC start relay mounts on the refrigerator compressor and briefly energizes the start winding, then automatically opens as it warms. Replacing a weak relay helps restore reliable compressor starts and consistent cooling. What it does:

• Provides momentary power to the compressor's start winding at startup; the PTC element opens as it heats
• Helps ensure smooth compressor starts and reduces repeated start attempts
• Signs of a failed start device can include no cooling because the compressor won't run
• Clicking or buzzing from the compressor area every few minutes
• Compressor starts intermittently or stops shortly after starting

• Includes: 1 PTC start relay

• Disconnect power and pull the refrigerator forward to access the rear service area
• Remove the rear panel to reach the compressor compartment
• Unplug the wire harness and pull the old relay straight off the compressor terminals; note its orientation
• Push the new relay fully onto the compressor prongs, reconnect the harness, reinstall the panel, and restore power

Kit includes relay, overload, cover and instructions.

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

The Water-Level Pressure Switch is an OEM part for Whirlpool washers. It is responsible for monitoring the water level inside the washer's tub during different cycles. This switch detects changes in air pressure as the water level rises or falls, communicating these variations to the washer's control board. 

Symptoms of a faulty water-level pressure switch include:

• Incorrect water levels during the wash cycle
• Washer not filling or draining properly
• Error codes related to water level

A bad water-level pressure switch can occur due to various factors, such as clogs or blockages in the air hose, a malfunctioning switch mechanism, or electrical issues. If you notice problems such as the washer not filling or draining properly, water levels that are too high or too low, or error codes related to water level, it may be time to replace the water-level pressure switch.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.

Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.

Symptoms of a faulty overload protector include:

• Refrigerator fails to properly cool or the compressor does not run
• Circuit board or electrical component failure or burnout
• Lack of cold air production and higher than normal freezer/fridge temperatures

This OEM LG part is also compatible with some Sears/Kenmore models.

The door switch detects whether the dryer door is open or closed, enabling the motor and heater only when it's safe. Replacing a failed switch restores proper start/stop control and drum light behavior.

• Senses door position and completes or interrupts the dryer's run/heat circuits
• Shuts the dryer off when the door opens for safety
• Common symptoms: dryer won't start with the door closed; doesn't stop when door opens; drum light stays on or won't turn on
• Intermittent operation when the door is moved or pressed

• Disconnect power before servicing; allow components to cool
• Access the switch from the door opening or front panel; remove screws or release locking tabs
• Note wire positions and transfer them one at a time to the new switch
• Verify operation before reassembly: dryer should not run with the door open; drum light should respond

This starter is the compressor start relay that briefly powers the start winding to get the compressor turning. Replacing a weak or failed starter can restore reliable compressor startup and consistent cooling performance.

• Engages the compressor's start winding at power-up, then disengages as the motor reaches speed
• Helps prevent repeated clicking, stalling, and overheating at the compressor
• Common symptoms include no cooling while fans run, compressor hums or clicks but won't start, or short-cycles on the overload
• Physical signs may include heat damage or a burnt odor on the original start device

• Disconnect power and allow the compressor to cool before service
• Discharge any capacitors per manufacturer instructions
• Note wire positions and terminal orientation; transfer leads one at a time
• Push the relay fully onto the compressor pins; ensure a secure fit without bending terminals

This power relay is an electromechanical switch with a 48 VDC coil that lets the control board safely turn high-voltage components on and off. Replacing a weak or sticking relay helps restore consistent, reliable operation. What it does:

• Uses a 48 VDC coil signal from the control to open/close internal contacts
• Switches AC line power to high-demand loads (e.g., heater, motor, fan, or compressor)
• Helps maintain stable cycling and prevents intermittent operation
• Helps with symptoms such as no heat or no run, intermittent operation, clicking with no activation, or a component stuck on

• Power relay (48 VDC coil)

• Disconnect power to the appliance before servicing; allow capacitors to discharge
• Note/photograph wire locations and move wires one at a time to matching terminals
• Ensure terminals are fully seated; replace any burnt or loose connectors
• Mount in the original orientation and secure firmly to prevent vibration

This broken belt switch is a dryer safety switch that senses drive belt tension and opens the motor circuit if the belt breaks or slips off. Replacing a failed switch can resolve a no-start or no-tumble condition. What it does:

• Monitors drive belt tension via the idler assembly
• Interrupts power to the motor when the belt is broken or not tensioned
• Helps prevent heating without airflow when the belt has failed
• Symptoms can include: dryer won't start, drum won't turn, or the dryer stops as soon as the Start button is released

• 1 switch

• Disconnect power; for gas models, shut off the gas supply
• Access the switch near the idler pulley by removing the lower/front panel per your model
• Transfer wires from the old switch to the new one; mount securely with the actuator aligned to the idler arm
• Run a brief test cycle