Kenmore Washer 110.47571601 (11047571601, 110 47571601) Parts

• Will not drain
• Noisy
• Burning smell
• Pumps but will not spin

There was a loud noise from my washer during the drain cycle. (The washer seemed to drain just fine.) It was pretty easy to determine that the noise was coming from the drain pump. (Which for my washer is behind the front lower inspection panel on the right side front.) I inspected the outside of the pump for any physical damage and verified no issues with the pump or the mounts. Everything seemed ok. I then checked the drain pump filter(You will need something to catch water if you do... Read more

I followed the very well made repair video for this particular part. The total time it took for the repair was under 20 minutes. But I have a suggestion for the repair video and that is to emphasize that when reinstalling boot. Have the tachnician point out that there are drain holes in the boot that need to be situated and reattached toward the bottom of the washer chassis. Unfortunately I had to redue and double the repair time because the wash water would not drain properly during wash... Read more

• Lid or door will not open
• Won't start

Did lots of internet research. Narrowed problem down to three things - door lock latch, control unit, and motor control unit. Figured out how to run the diagnostic test program, which showed a F22 (door lock) error. Removed and ohm tested the door lock (pins 1 & 3). Found door lock latch to be defective. ordered new one and installed it. YouTube video helped a lot. https://www.youtube.com/watch?v=_SjU6k5bpSs So far, so good. Have only done a few loads. New door lock latch tested fine. Read more

• Lid or door won't close
• Lid or door will not open

I removed the two screws and all the pieces that were broken. Went online to Appliance parts.com, searched for the part using the model number from the machine and ordered the part . part arrived in 2 days and with a Phillips screwdriver was installed in less than 5 minutes. Read more

• Will not fill with water
• Will not stop filling with water

The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads. Read more

Watched a youtube video and it was easy to do. Read more

Replaced It With New One Read more

Followed your video instructions. It was invaluable. The toughest part was getting the seal on the back of the drum. Your technician made it look very easy. Once that was on, the rest was pretty easy. The control panel on my Whirlpool Duet washer had a holding screw at the bottom center of it. It wasn't shown in the video, but it was easy to figure out. If you are changing the boot, change the clamp as well. Read more

Touch up paint Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

• Will not agitate

Using a nut driver I removed the sheet metal screws, removed the old belt and replaced it with the one. An easy repair. Shipping was EXCELLENT! Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more

Took the old part off and fitted the new one. I used the old plastic ball from the old hose and it worked fine. Next time I would replace the original clamp with a 4 inch hose clamp. The original clamp is way tooooooooooo hard to put back on....with a different clip it would be a 10 minute job at most. Read more