Kenmore Med Line Mover Start Switch Parts

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Won't start
• Element will not heat

After an internet search, the likely problem was a faulty "Element Switch.." I actually unplugged the stove and removed the switch (I did NOT disconnect the wires). I obtained the part number on the switch, disassembled it, observed that the contacts were highly degraded, reassembled the switch and reinstalled it back into the stove. This all provided confidence the SWITCH was faulty. One switch on the AppliancePartsPros.com website (AP2591804) looked exactly like the switch in the stove... Read more

• Won't start
• Element will not heat

The fix was to replace the infinite control switch on my Whirlpool range. A simple task. Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Won't start

I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

• Won't start

Noticed Rolls on the top shelf no longer frozen, though the meat around it still was. Note: This is a good test, keep something that thaws quickly and is not expensive on top shelf, to act as a barometer for your freezer health! I first found a trip online to advance the defrost timer, as a failed timer is a common issue. I advanced the timer, but nothing happened. I emptied the freezer, then removed the thermostat and tested it. No continuity! With the Freezer continuing to thaw, I... Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

• Element will not heat

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

• Clicking sound
• Won't start
• Freezer section too warm
• Fridge too warm

Removed back cover and installed new start device. Plugged in refridgerator and it runs like new. Read more

• Won't start
• Too warm
• Fridge too warm
• Freezer section too warm

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more