Pdt845sblts Parts

The Door Latch is an OEM replacement part for GE dishwashers. It serves the critical function of securely keeping the door closed during wash cycles through its engaging bolt design.

Over extended use, aspects of the latch can degrade such as worn plastic catch areas, loosened screws, or a faulty latch hook mechanism. Causes are generally normal wear and tear. 

Symptoms of a bad latch include: 

• The door not closing fully or popping open accidentally  
• Inability to fully lock or latch no matter how hard the door is pressed
• Damaged or stripped screws holding the mechanism 

This OEM replacement part is compatible with Hotpoint, RCA and some Kenmore models as well.

Restore smooth, dependable rack movement. This kit replaces worn carriers and rollers so the lower dishrack glides in and out without binding, derailing, or dropping.

What it does

• Supports and guides the lower rack along the tracks
• Replaces broken, missing, or flat-spotted wheels and cracked carriers
• Helps prevent the rack from popping off the rails during loading
• Reduces drag that leads to stiff, uneven rack travel

What’s included
Four carrier brackets, four roller wheel brackets (covers), and eight wheels — a complete set of four assemblies.

Install notes

• Disconnect power before servicing the rack area.
• Pull the lower rack out; swap one assembly at a time to match left/right orientation.
• Fully seat tabs/locks on each carrier; verify wheels roll freely.
• Best practice: replace all four together for even tracking, then run a quick test cycle.

This flexible door gasket seals the dishwasher tub opening to keep wash water inside the cabinet. Replace a worn or flattened gasket to stop leaks and restore a tight, quiet door seal.

• Compresses between the door and tub to prevent water from escaping during wash and rinse cycles
• Helps reduce moisture at the front corners and under the door
• Common failure signs: water leaking at the bottom/front of the door, visible tears, cracks, or permanent flattening of the seal
• Can also help if the door feels loose or doesn't seal evenly

• Disconnect power and turn off water before service
• Open the door and pull the old gasket straight out of the groove; clean the channel of debris and buildup
• To ease installation, warm the new gasket to relax it, then press it into the channel starting at the top center and work evenly down both sides
• Close the door for several minutes to help seat the new seal, then run a short cycle to check for leaks

The Lower Rack Roller is an OEM replacement part for GE dishwashers. This small but crucial component allows for smooth and effortless movement of the lower dish rack during loading and unloading.

Symptoms of needing to replace the lower rack roller include:

• Difficulty in sliding the lower rack in or out
• Excessive noise or grinding during rack movement
• The rack becoming stuck or not rolling smoothly
• Visible wear, cracks, or damage to the roller itself

Causes of a faulty lower rack roller can include normal wear and tear over time, exposure to heat or moisture, or physical damage due to impact or mishandling.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.

The Silverware Basket Assembly is an OEM replacement part for GE dishwashers. This basket is designed to hold and organize silverware and utensils during the dishwashing cycle. It ensures that utensils are properly spaced and positioned to receive optimal cleaning, preventing them from nesting together and ensuring thorough water circulation.

Over time, the silverware basket can become worn or damaged due to regular use and exposure to high temperatures and detergents. Cracks, breaks, or missing sections can occur, leading to utensils falling through or becoming improperly cleaned.

Symptoms of a bad silverware basket assembly include:

• Utensils falling through the bottom or sides of the basket
• Cracks, holes, or broken sections in the basket
• The basket not fitting securely in its designated place within the dishwasher
• Rust or discoloration affecting the basket's integrity

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Upper Dishrack Rail is an OEM part for GE dishwashers. It supports the upper dishrack, allowing it to slide in and out smoothly for easy loading and unloading of dishes. This rail ensures that the dishrack remains stable and functions correctly during the wash cycle.

You should replace the upper dishrack rail if it becomes damaged or worn out. Over time, the rail can suffer from wear and tear due to the constant movement of the dishrack. Accidental impacts or bending can also compromise the integrity of the rail, leading to improper function.

Symptoms of a bad upper dishrack rail include:

• The upper dishrack not sliding in and out smoothly
• The dishrack becoming unstable or falling off the track
• Visible damage or bending of the rail
• Increased noise during the operation of the dishwasher

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Tub to Cabinet Trim is an OEM part for GE dishwashers. This kit includes the trim that fits around the edges of the dishwasher tub, providing a finished look and sealing the edges to prevent leaks and debris from getting into the internal components. The trim measures approximately 26 x 2 inches.

Causes of a bad tub trim can include wear and tear from regular use, damage from cleaning or loading dishes, and exposure to moisture and detergents which can degrade the material over time. Improper installation can also result in poor fitting or gaps in the trim.

Symptoms of a bad Tub Trim Kit include:

• Visible gaps or loose trim around the dishwasher tub
• Leaks around the edges of the tub
• Accumulation of debris in the trim area
• The dishwasher door not closing properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Cable and Spring Kit is an OEM part for GE dishwashers. This kit includes the necessary cables and springs that connect to the dishwasher door, allowing it to open and close smoothly and securely. The components work together to provide the right tension and balance, preventing the door from falling open too quickly or not staying closed properly.

Common causes of a bad door cable and spring include wear and tear from regular use, accidental damage, or corrosion over time. When these components fail, the door may become difficult to operate or unsafe.

Symptoms of a bad Door Cable and Spring Kit include:

• The dishwasher door falling open too quickly
• The door not staying closed securely
• Difficulty in opening or closing the door
• Unusual noises when operating the door

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Latch Strike is an OEM part for GE dishwashers. It ensures the dishwasher door latches securely, allowing the appliance to operate only when the door is properly closed.

Causes of a bad door latch strike can include wear and tear from regular use, damage from slamming the door, or misalignment due to repeated opening and closing.

Symptoms of a bad door latch strike include:

• The dishwasher door not latching securely
• The dishwasher not starting or stopping mid-cycle
• Leaks around the door during operation
• Difficulty in closing the door properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Vent Seal is an OEM part for GE dishwashers. Located within the front dishwasher door, it functions to control moist air circulation and maintain humidity levels inside the wash chamber.

Causes of a bad door vent seal can include cracking of the flexible seal material. Mineral or soap deposits may also compromise sealing integrity.

Symptoms of a bad vent seal include:

• Excess condensation buildup within the door interior
• Water leaks detected around door ventilation openings
• Drying and sanitization issues related to inconsistent humidity levels

This GE OEM replacement part is also compatible with Hotpoint, RCA, and select Kenmore-branded dishwashers.

The Folding Tine Row Clip is an OEM part for GE dishwashers. It is located on the side of the dishwasher's lower rack and holds the folding tine row securely in position. It ensures that the folding tines, which can be adjusted to accommodate different dish sizes, remain stable during the wash cycle.

Causes of a faulty or damaged folding tine row clip can include regular use, wear and tear, or breakage. These factors can result in issues such as the folding tine row becoming loose or unstable, difficulty in adjusting the tines, or the tines not staying in the desired position.

Symptoms of a bad folding tine row clip may include:

• The folding tine row becoming loose or falling out of place
• Difficulty in adjusting the tines or keeping them in position
• Unstable or wobbly tines during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Mounting Bracket is an OEM replacement part for GE dishwashers. This bracket secures the dishwasher in place underneath the kitchen countertop. 

Causes of failure relate to stresses of a heavy dishwasher pushing down against the countertop edges combined with constant machine vibration over extended service life. 

Symptoms of a cracked or damaged mounting bracket include:

• Excessive movement play or sloshing of the installed dishwasher  
• Strange noises when the dishwasher is running
• Difficulty removing or installing the dishwasher   
• Visible bending of bracket components out of intended position

This genuine GE bracket is compatible with Hotpoint and RCA dishwashers.

The Folding Tine Row is an OEM part for GE dishwashers. Located on the bottom dish rack, it functions to fold down during wash cycles for improved water coverage beneath flatware and smaller items.

Causes of a bad folding tine row can include broken or cracked tines from years of repeated folding motions. Mineral accumulation on hinge points may also affect smooth operation.

Symptoms of a bad Folding Tine Row include:

• Inability to fold down or remain in the folded-down position
• Improper water coverage for small plates and utensils on the bottom rack
• Items not getting thoroughly washed beneath the tine area
• Loose fasteners or components that create noise during cycling

This GE OEM replacement part is also compatible with Hotpoint, RCA, and select Kenmore dishwashers.

The Folding Tine Row is an OEM replacement part for GE dishwashers. Located along the lower rack, it contains movable plastic tines that flex to accommodate varying dish sizes and configurations. Proper functioning tines are essential for optimizing wash coverage and cleaning results. 

Causes of a bad folding tine row include cracked or broken plastic from years of repeated movement. Mineral buildup may cause tines to become rigid or stuck over time as well.

Symptoms include: 

• Inability to fit larger pots, pans, or casserole dishes  
• Items not getting fully washed due to restricted spray access
• Food particles or residue left behind in hard-to-reach areas  
• Warped or misaligned tines that snag during loading/unloading

Compatible models include Hotpoint, RCA, and some Kenmore dishwashers. 

The Sump Gasket is an OEM part for GE dishwashers. It forms a watertight seal around the sump area, preventing leaks and ensuring proper water circulation within the dishwasher.

Causes of a bad sump gasket include exposure to high temperatures, general wear and tear over time, and damage from cleaning chemicals.

Symptoms of a bad sump gasket include:

• Water leaking from the bottom of the dishwasher
• Poor cleaning performance due to improper water circulation
• Visible cracks or deterioration in the gasket material
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Mid Conduit Blaster is the mid-level water outlet in your dishwasher's wash system. It directs pressurized water through the middle conduit, helping deliver consistent spray to the middle rack for reliable cleaning performance.

• Directs wash water into the mid-level conduit and spray system
• Helps maintain proper pressure and spray coverage for middle-rack cleaning
• Damage or clogging can lead to weak spray, poor cleaning on the middle/upper racks, or unusual noise
• Replace if cracked, missing, or leaking at the conduit connection

• Disconnect power and shut off the water supply before servicing
• Pull out racks as needed to access the mid-level conduit
• Release locking tabs or fastener, remove the old outlet, and seat the new one fully in the correct orientation
• Restore power and water, then run a short cycle to check spray action and for leaks