Pr-4 Parts

ST10-16 X 7/16"

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This flanged hex nut is used in various models of lawn and garden equipment. The nut is considered a standard hardware part that may have multiple applications on different units. It is typically used along with a bolt or screw to provide a secure hold for various components. This nut is a small part and can become lost in the process of other repairs. It can also break or strip the threads due to regular wear and tear, impact damage, or another issue. If this nut is broken or missing, it needs to be replaced immediately. Replacing the hex nut with a genuine OEM part will ensure equipment is always in proper working order. This OEM hex nut is designed for use in select Craftsman and Husqvarna equipment. It is manufactured by Husqvarna as an exact replacement for the original nuts that came with the machine. This part can fit on more than 150 machines, including lawn mowers, tractors, snow blowers, and trimmers from both brands. Owners will want to check their parts diagram for the exact location(s) and application(s) of this nut. Since it is standard hardware, some people purchase multiple quantities to keep extra parts on hand in case of emergency.

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

This handguard is made to be used on several models of chainsaws by major lawn and garden manufacturers. The purpose of the handguard is to engage the chain brake if it is pushed forward. A secondary function of the handguard is to protect the user's hands from an injury that could be caused by the bar and chain on the chainsaw. The part is made of durable plastic but can become damaged over time, through use, or impact.A visual inspection will show if the handguard has become cracked, fallen off, or is broken in other ways. If this occurs, the handguard will need to be replaced before using the chainsaw. The replacement should be done while using work gloves. Place the chainsaw on a flat surface and remove the spark plug wire first. A socket set and a screwdriver can be used to remove the old handguard. Install the new one and reassemble other parts before use.This is a genuine OEM replacement part directly sourced from the manufacturer. It's sold as an individual part. The component is designed for use with chainsaws manufactured by Poulan, Poulan Pro, and Craftsman.

The Fuel Pick Up Assembly is an OEM part for Husqvarna outdoor power equipment, including chainsaws, trimmers, and blowers. This assembly is responsible for drawing fuel from the tank to the carburetor, ensuring the engine receives a steady supply of fuel for optimal performance.

Over time, the fuel pick up assembly can become clogged or damaged due to debris in the fuel, exposure to ethanol-blended gasoline, or regular wear and tear. If the fuel pick up assembly is compromised, it can lead to poor engine performance or difficulty starting the equipment.

Symptoms of a bad fuel pick up assembly include:

• Engine not starting or hard to start
• Engine stalling or running inconsistently
• Reduced power or performance
•  Visible damage or clogging in the fuel line

This OEM Husqvarna part ensures proper fuel delivery and compatibility with your outdoor power equipment.

The chainsaw carburetor mixes air and gas before this mixture makes its way to the engine. If this is not working correctly, the engine receives a less efficient gas supply or no gas supply at all. If your chainsaw has a full tank of gas but will not start or stops just after starting, the carburetor may need to be replaced. While carburetors can be cleaned to get them working again, they often need to be replaced if they have become too clogged. Depending on what you can reuse from your old carburetor, you may need to order new gaskets as well to ensure an airtight seal. A screwdriver, a nut driver, and a socket wrench set may be needed to complete this repair. This chainsaw carburetor is sold individually from other parts, but it does include the primer bulb. It is compatible with Craftsman and Poulan chainsaws. This chainsaw carburetor is a genuine OEM part.

This clutch washer kid includes a clutch, a washer, and a clip. A washer helps to protect the engine from unwanted pressure at the joint where two parts connect. Washers help to spread the pressure evenly so that the fastener doesn’t move, which would cause corrosion and friction. Washers can wear down or corrode over time, leading to unwanted pressure in the chainsaw’s engine. Based on the location of this washer, replacing it may require different steps to take apart the engine. Be sure that the engine has cooled completely before attempting any repairs. This part is compatible with Poulan and Craftsman chainsaws and is a genuine OEM part sourced directly from the manufacturer.

When used regularly, protects your solid cooking elements from rusting and spotting. Helps maintain the original black matte appearance.

The replacement handle bolt here can be used for lawn and garden equipment. The handle bolt is used with the handle knob to help secure the upper and lower handles of the machine together. If the bolt is damaged or missing, it will not be possible to secure the handles properly. The handle bolts are durable and made from metal, but they could become damaged due to corrosion or natural wear. In other cases, they could become lost. In either case, they will need to be replaced. The replacement is simple and will not require any tools, as the square part of the bolt will fit into the handle perfectly. The handle knob will then be used to keep it in place. The handle bolt is a genuine OEM Part for lawn mowers and snowblowers. It is compatible with some models from Husqvarna, Murray, Weed Eater, Poulan, Jonsered, Craftsman, and Ryobi. It should be noted that this product is sold individually, and the handle knob is not included.

A lawnmower, weed whacker, or trimmer is exposed to a lot of flying debris, and this puts many parts at risk of becoming clogged with grass and other materials. This cover is designed to prevent any debris from reaching the interior of the wheel or the axle. If a large amount of grass or clippings accumulate inside of the assembly, the machine will be almost impossible to move forward - whether self-propelled or manually operated. This cover prevents that from occurring and simply kicks it back in the direction it came. It does take a lot of wear and tear. Installing it is extremely easy and requires little more than a wrench. Even if the cover is aged, or broken, it will remove easily and take minutes to replace. Expect to replace this at least once over the average lifespan of a trimmer. This works with Husqvarna, Poulan, Craftsman, Ariens, Weed Eater, Jonsered, and Murray makes and models. It is a genuine OEM part sold individually.

The recoil spring is a vital part of the starter mechanism in chainsaws. It will apply tension on the pulley, which allows it to retract the rope. Without a working spring, it will be difficult or even impossible to start the chainsaw. While the metal springs are durable, they could start to wear out over time and will no longer be effective. In addition, the springs could suffer damage or could become corroded. They could also be lost when making other repairs to the chainsaw. If there is any issue with the spring, it will require a replacement. This authentic OEM replacement recoil spring is sold individually. The chainsaw recoil spring is compatible with several brands including Poulan, Poulan Pro, Husqvarna, Jonsered, Craftsman.

This wire harness assembly is an authentic replacement for chainsaws. It is supplied from the manufacturer. The wire harness assembly connects to the ignition module. It is made of two wires. One of the wires carries the power from the coil to the switch, while the other wire attaches to the engine ground on one side and has a switch contact on the other side. The wires have a rubber insulated coating that helps to protect them from high heat. These wires can suffer damage in many ways. They could become frayed or cut, they could have been subject to extremely high temperatures, and more. When they are damaged, it can cause a continuity loss in the circuit which can shut off the saw. Owners should look for broken or frayed wires. They can also use a multimeter to check the wires for continuity. If there are issues, the wires should be replaced right away. The chainsaw wire harness assembly is a genuine OEM replacement part for use with chainsaws. The assembly is sold individually. It will work with select chainsaws from Craftsman, Husqvarna, Poulan, and Poulan Pro.

This chain brake is made to connect above the drum of a chainsaw. It has a metal band that goes around the drum and a handguard that also connects to the brake. When the guard is pressed forward, the brake band tightens on the clutch drum, making the chain stop immediately. The brake is pre-assembled and consists of both metal and plastic parts. The spring, brake band, and linkage are all metal, and the housing is plastic. A common chain brake problem is the brake band becoming worn out or damaged. This causes the brake to no longer stop the chain fast enough or at all. This can be incredibly dangerous, so it’s important to check the brake regularly. Installing a new chain brake is straightforward with this genuine OEM part sourced directly from the manufacturer. Just remove the clutch cover assembly, take off the old chain brake, and screw in the new kit. Be sure to wear gloves and let the engine cool completely before making repairs. Compatible with Craftsman, Poulan, and Poulan Pro chainsaws. Sold individually.