Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Leaking water from your refrigerator or no water/ice from dispenser? This water inlet valve controls flow to ice maker and dispenser. DIY repair in 30 min.
I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more
Ice maker stopped making ice or won't eject cubes? This ice maker assembly fixes frozen or stuck trays. DIY install in 30-60 minutes with basic tools.
Replaced ice maker. Some confusion as to which part # it was as the model number cross reference shows the one I purchased was not for my model refrigerator when it actually was. Secondly, a few comments from others said the switch out was simple. Only 3 screws holding in the ice maker although one of the three was in a tight spot . That is technically true. Three screws do hold the ice maker on the door , however, you must also remove the door panel behind the ice maker to get to the wiring... Read more
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Ice maker stopped producing ice or cycles too slowly? This complete ice maker assembly replaces a faulty unit. DIY-friendly installation in 10-15 minutes.
Ice sensing lever (keyed onto mtr shaft) found down and would not budge. Also, test button (hidden beneath mtr) only 'beeped' when pushed. The 10 pin connector's 'clip' is also hidden against roof of freezer - mine broke but connection still seems secure. New unit was exact fit - test button (now) cycles thru one cycle of rotation and H2O fill with no beeps.... 18 hrs later, bin is half full....ice for the summer :) Remove freezer door (front) so you can lay down and look up. Cold plastic... Read more
Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.
Ordered a new compressor and repaired by 3rd party. Read more
Fridge freezing food or not cooling? This temperature sensor monitors internal temps and signals the control board. Fixes ER FF errors. Easy install.
I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more
If your refrigerator is noisy or not cooling evenly, the evaporator fan motor may need replacement. 15-30 minute repair requires freezer panel removal.
Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more
Controls ice dispenser door opening and closing. Replace if door won't open, stays open, or motor makes no sound when dispensing. Mounts behind dispenser trim.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Refrigerator mullion door won't close or seal properly? This spring operates the center divider flapper door. DIY-friendly installation in 5 minutes.
Went looking for the spring for my refrigerator door mullion and it is not available for my model. Was told that I had to purchase the entire mullion for $130. Saw some videos on the web about replacing the spring making sure I got the one with the right number of coils. My broken one had 6 coils, I looked at the picture of the spring and counted six coils so I bought it and it worked fine. Read more
Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.
1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more
Dual roller wheel assembly that mounts to the rear wall of the freezer drawer. Replace when wheels are missing, broken, or cracked for smooth sliding.
With your part and 5 minutes. Quick and easy. Read more
Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.
Replaced icemaker Read more
Fix a dispenser that won't stop running or fails to dispense ice or water. This switch activates your dispenser when pressed. DIY-friendly repair.
Replacement fresh room tray assembly for LG and Kenmore refrigerators. Install this tray if yours is cracked, broken, or has a damaged handle.
Ordered replacement drawer, new drawer was an exact replacement even though the part number had been changed. Read more
Compressor running hot or error code 22? This thermistor assembly monitors compressor temperature to prevent overheating. 10-minute DIY repair.
Replace thermistor. Explained to home owner either thermistor or compressor since it was running hot but only 10 minutes to change out. Luckily client still has warranty on fridge to replace old compressor and thermistor. Read more
Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.
Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more