Parts for Maytag 7MMVWB950AG0: 01 - Top And Cabinet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

Color: Grey

This sound absorber is an OEM-style insulation pad designed to reduce washer cabinet noise and rattling for a quieter cycle. It mounts inside the appliance cabinet to help dampen vibration and airborne sound. What it does:

• Dampens vibration and reduces cabinet noise during spin and agitation
• Helps minimize rattling from internal components for a quieter operation
• Supports stable operation by providing a cushioned barrier between parts and the cabinet
• Commonly replaced when padding is torn, missing, or compressed

• One sound absorber insulation pad

• Disconnect power and water supply before starting any repair
• Access may require removing outer cabinet or panels; follow your model's service manual
• Use proper fasteners and placement as shown in OEM diagram; avoid altering material

Small but essential, this drain hose retainer is a clip that secures the hose in place during use or storage. It keeps the hose properly routed to help prevent kinks, pull-outs, and leaks. What it does:

• Holds the drain hose to the cabinet/frame for correct routing or stowage
• Helps prevent kinks, abrasion, and strain that can cause poor draining or leaks
• Replaces a broken, warped, or missing retainer so the hose stays put
• Common symptoms: hose won't stay clipped, falls during operation, visible damage, water near hose path

• 1 drain hose retainer

• Disconnect power and turn off the water supply before servicing
• Access the hose routing area and remove the damaged retainer
• Position and fasten the new retainer in the same location; route the hose through it
• Run a brief test to ensure secure routing and no leaks

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This flexible gasket creates a tight seal around the appliance opening to help keep temperature and moisture where they belong, reducing leaks and improving performance. It's a direct-replacement part designed to restore proper sealing. What it does:

• Forms an airtight/watertight barrier at the door or access opening
• Prevents leaks and spills from escaping the cabinet or tub
• Helps maintain internal temperature and prevents moisture intrusion
• Reduces frost buildup and condensation caused by poor sealing

• One replacement seal

• Inspect mounting channel and retainers for damage before installing the new seal
• Clean the sealing surface and allow it to dry for a secure fit
• Peel-back adhesive or align retention tabs as required by your model; avoid stretching the gasket

This factory-style screw secures panels, brackets, and internal components in your appliance. It replaces a missing or damaged fastener to restore a tight, aligned, rattle-free fit.

• Provides the correct #6-32 machine thread to match original tapped holes
• Secures covers, control housings, brackets, or trim in place
• Helps reduce vibration or rattling from loose panels
• Common signs you need this fastener: missing screw, stripped/damaged screw, loose or misaligned component

• Disconnect power and shut off water/gas before service
• Match length and head style to the original location before installing
• Start threads by hand to avoid cross-threading; tighten only until snug
• Use the correct driver or nut driver specified for your model's fastener head

Right side hinge.

Left side hinge

This condenser tie is a small plastic wire tie used to secure the condenser assembly or related wiring and tubing in place. It helps prevent rubbing, vibration noise, and loose routing that can cause wear or interference. What it does:

• Secures condenser coils, wiring harnesses, or drain/tubing to the appliance frame
• Prevents rubbing and vibration that can cause noise or premature wear
• Keeps wiring and tubing routed away from moving parts and hot surfaces
• Helps maintain tidy component placement for reliable operation

• Disconnect power to the appliance before servicing.
• Use pliers or a tie tool to snug the tie; trim excess tail flush to avoid sharp edges.
• Single-use plastic ties may need replacement if cut for removal.
• Route tied components clear of fans, sharp edges, and heating elements.

Hinge bearing that supports the appliance door hinge for smooth, stable movement and helps prevent door sag or noisy operation. Replacing a worn bearing restores proper door alignment and reduces hinge wear. What it does:

• Provides a low-friction pivot for the door hinge so the door opens and closes smoothly.
• Prevents binding, grinding, and uneven door movement caused by a worn hinge pivot.
• Helps maintain proper door alignment to avoid gaps or incomplete latching.
• Common symptoms: door hangs, squeaks, clicks, binds, or feels loose at the hinge.

• Always disconnect power (and water for dishwashers) before beginning repairs.
• Access typically requires removing the door or hinge trim—keep fasteners organized.
• Replace only with the matching bearing; test door operation before reassembly.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This leveling foot assembly supports the base of your appliance and provides height adjustment. Leveling the cabinet reduces rocking and vibration and helps doors and components align and seal correctly for smooth, quiet operation. What it does:

• Threads into the base/frame to set height and stabilize the cabinet
• Levels the appliance on uneven floors to reduce wobble and vibration
• Helps maintain proper door alignment and sealing
• Replace if the foot is missing, cracked, stripped, or seized

• 1 leveling foot assembly

• Disconnect power and, if applicable, shut off water before servicing
• Carefully move or tilt the appliance with a helper to access the foot; support it securely
• Unthread the damaged foot; thread the new foot by hand to avoid cross-threading, then adjust with a wrench as needed
• Verify level front-to-back and side-to-side; confirm the unit sits stable before returning to service

The fabric softener dispenser stores liquid softener and automatically releases it during the rinse cycle. Replace a cracked, clogged, or missing dispenser to restore reliable dispensing and reduce leaks or softener left behind. What it does:

• Holds liquid fabric softener and dispenses it at the proper time in the rinse cycle
• Helps prevent early release of softener onto clothes
• Common symptoms: softener not dispensing, softener remaining in the cup after the cycle, leaks/drips from the dispenser area, or visible damage/missing dispenser
• Can resolve clogs from residue buildup that interfere with siphoning/flow

• 1 fabric softener dispenser

• Disconnect power and turn off water supply before servicing
• Remove the old dispenser (pull straight up or release locking tabs, per model)
• Clean any residue from the mounting area; flush the new dispenser with warm water
• Seat the new dispenser fully and test with a small amount of water to ensure proper flow

Color: Grey

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This detergent dispenser assembly stores detergent and releases it at the right point in the wash cycle. Replace it to restore reliable soap dispensing and consistent cleaning when the cup door or mechanism fails.

• Holds detergent securely until the cycle calls for release
• Opens the detergent cup at the proper time for effective washing
• Helps prevent premature detergent loss and residue on dishes/clothes
• Common symptoms: soap door won't latch/open, detergent left in cup after cycle, visible cracks or leaks around the dispenser area

• Disconnect power and shut off water before service
• Access the dispenser at its mounting location; remove fasteners/release tabs and unplug the harness
• Seat the new assembly evenly on a clean surface to ensure a good seal; reconnect wiring
• Reassemble and run a test cycle to check for leaks

Color: Grey

This fresh-water nozzle assembly directs a controlled stream into the appliance during fill/dispense. Replacing a cracked or clogged nozzle restores proper flow and helps reduce splashing, misdirected spray, or dripping at the opening. What it does:

• Shapes and directs fresh water into the tub/dispenser area
• Helps prevent spray, backflow, and mess around the opening
• Common symptoms: weak or misdirected stream, dripping after fill/dispense, leaks near the opening, visible cracks or mineral buildup on the nozzle
• A kinked or brittle attached tube can restrict flow or leak

• One fresh-water nozzle assembly

• Disconnect power and shut off the water supply before servicing
• Access the nozzle area; remove necessary panels or trim
• Release retaining clip(s), disconnect tubing, and note routing before removal
• Install the new assembly fully seated; restore water/power, check for leaks, and run a test fill to flush air/debris

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lid Lock Assembly is an OEM part for Whirlpool washing machines. It ensures the washer lid is securely locked during operation, preventing it from being opened mid-cycle and ensuring safe and efficient washing.

Causes of a bad lid lock assembly can include wear and tear from frequent use, electrical issues such as short circuits, and physical damage from impact or mishandling. A malfunctioning lid lock can disrupt the washing cycle, leading to incomplete washes or safety concerns.

Symptoms of a bad lid lock assembly include:

• The washer not starting or stopping mid-cycle
• Error codes indicating a lid lock issue
• The lid not locking or unlocking properly
• The washer lid feeling loose or failing to stay closed

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Grey

The Absorber is an OEM part for Whirlpool washing machines. It plays a role in minimizing vibrations and noise during operation by damping the mechanical movements within the machine. 

Causes of a bad Absorber can include the natural wear and tear from continuous use, degradation due to exposure to harsh chemicals or extreme temperatures, and mechanical failure from excessive loads or unbalanced cycles.

Symptoms of a bad Absorber include:

• Increased vibration or shaking during operation.
• Unusual noises like thumping or banging during the spin cycle.
• The washing machine moving excessively or "walking" across the floor.
• Uneven wear and tear on other washing machine components.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

Used from harness to top.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.