Parts for Whirlpool 7MWET4027HW0: Washer / Dryer Control Panel Parts

Note: 5  Position Switch
 

Note: 2-Position Switch

The Push to Start Switch is an OEM replacement part for Whirlpool dryers. Located on the control panel, it allows the user to initiate the drying cycle with the push of a button. This switch is designed to withstand the repetitive motions of starting countless loads over the dryer's lifespan.

Causes can be gradual wear of internal components like contact pads from activations, or moisture intrusion corroding circuit pathways over time.

Symptoms of a faulty push-to-start switch include:

• The dryer failing to start even when powered on
• Inconsistent or intermittent operation of the start button
• The dryer starting unintentionally without input

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Knob Kit is an OEM replacement part for Whirlpool washing machines and dryers. Including a set of premium knobs color-matched to the appliance controls, this kit restores complete interfaces whenever old or damaged buttons need replacing. The kit includes 1 timer knob and 3 control knobs.

Causes for replacement involve normal wear from repeated touching during cycles as well as impact damage from falls or button presses gone awry over many years of service.

Symptoms necessitating a new knob kit include:

• Cracked, broken or missing buttons impeding normal operations
• Loosened knobs slipping out of holes or wearing partial turns
• Discolored faded markings obscuring switch positions

This OEM Whirlpool part is also compatible with Maytag, Amana, and other major brands.

The Knob Kit is an OEM replacement part for Whirlpool washing machines and dryers. Including a set of premium knobs color-matched to the appliance controls, this kit restores complete interfaces whenever old or damaged buttons need replacing. The kit includes 1 timer knob and 3 control knobs.

Causes for replacement involve normal wear from repeated touching during cycles as well as impact damage from falls or button presses gone awry over many years of service.

Symptoms necessitating a new knob kit include:

• Cracked, broken or missing buttons impeding normal operations
• Loosened knobs slipping out of holes or wearing partial turns
• Discolored faded markings obscuring switch positions

This OEM Whirlpool part is also compatible with Maytag, Amana, and other major brands.

This electronic control assembly (CCU PIMA) manages wash cycles and user commands, restoring responsive control and cycle sequencing for compatible Whirlpool top-load washers. It replaces a failed or unresponsive main control board. What it does:

• Receives user inputs and runs the washer's control logic to start, stop, and advance cycles
• Controls power distribution to motors, valves, and sensors
• Restores normal electronic control when the washer has unresponsive buttons, blank/erratic display, or failure to start/complete cycles
• Works as the factory replacement main control assembly for units specified to use the PIMA CCU

• One CCU PIMA 120V control assembly

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges; avoid touching components or connectors to prevent ESD damage
• Basic mechanical skill required; may require panel removal and connector reconnection

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This Timer is the mechanical cycle controller for your appliance. It sequences power to components so cycles start, advance, and end at the proper times, helping restore dependable operation when the original timer wears or fails.

• Sequences power to motors, valves, and heaters according to the cycle selected at the timer shaft
• Advances the machine through each stage via a motor-driven cam and internal contacts
• Symptoms: cycle doesn't advance or stops mid-cycle
• Symptoms: appliance won't start or only starts intermittently
• Symptoms: runs past the end of the cycle or won't shut off

• Disconnect power before servicing; shut off water supply
• Photograph wiring and transfer wires to the same labeled terminals one at a time
• Reuse the original mounting hardware, dial, and knob
• After installation, run a short test cycle to ensure the timer advances properly

This hinge bracket secures a refrigerator door hinge to the cabinet, restoring proper door alignment and support so the door seals and closes reliably. Designed to replace a worn, bent, or broken hinge mounting bracket. What it does:

• Provides a stable mounting point for the door hinge assembly to prevent sagging or drooping
• Restores correct door alignment to improve sealing and reduce cold air loss
• Stops excess movement or rattling at the hinge area
• Helps eliminate door-binding or uneven gaps that keep the door from closing fully

• Unplug the appliance and remove food/items from the door before starting
• Support the door while removing/installing the bracket to avoid damage or injury
• Reuse or replace fasteners as required; tighten securely but avoid over-torquing
• After installation, check door alignment and gasket seal; make minor adjustments as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance components in their intended positions. Swapping a missing, stripped, or corroded screw helps stop rattles and keeps panels, brackets, and internal parts tight for reliable operation.

• Fastens panels, brackets, or internal parts where specified by your model
• Helps reduce vibration and rattling caused by loose hardware
• Restores alignment when an original screw is missing or damaged
• Replace if threads are stripped, head is rounded, or corrosion is present

• Disconnect power and shut off water or gas before service
• Verify the exact location using your model's parts diagram/IPL
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or spacers if present

This control panel is the user interface assembly that lets you operate and program the oven or range. It restores button access and display feedback so the appliance can accept cooking commands and settings. What it does:

• Provides the touchpad/buttons and display area for selecting oven functions and temperature
• Sends user commands to the oven control so cycles, timers, and settings start as selected
• Commonly replaces a panel with unresponsive buttons, missing/blank display segments, or incorrect feedback
• Helps resolve issues where the oven won't accept inputs even though power is present

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle the panel and display lens carefully to avoid scratches or damage
• Use proper tools to remove mounting screws and detach wiring connectors gently