Parts for Thermador PDR366ZS: 08 - Oven Liner Parts

This flexible door seal/gasket creates a watertight barrier around the appliance door to help prevent leaks and keep internal temperatures stable. Replacing a worn seal restores proper sealing for reliable operation. What it does:

• Seals the door edge to prevent water from leaking during cycles
• Helps maintain internal temperature and cleaning performance
• Reduces moisture buildup and prevents odors from trapped debris
• Restores proper door alignment when the old seal has become misshapen or torn

• Disconnect power and water supply before starting any repair
• Remove the old seal by gently pulling from the door channel and clean the channel of debris
• Press the new gasket into the channel evenly, working around the entire door; ensure the seal is fully seated and not twisted
• If clips or retainers are present, verify they are correctly engaged; do not use sharp tools that can nick the gasket

The temperature sensor is an electronic probe that monitors internal appliance temperature and reports it to the control so it can regulate operation. Replacing a failed sensor restores more accurate temperatures and can clear temperature-related error codes. What it does:

• Senses internal temperature via resistance changes and sends the signal to the electronic control
• Helps the control reach and maintain the set temperature during operation
• Common failure symptoms: too hot/cold, won't reach set temp, long/short cycles, temperature error codes
• Can cause preheat to stall or the unit to shut off early (model dependent)

• Includes: 1 temperature sensor

• Disconnect power at the breaker before servicing
• Location and access vary by model; typically mounts with screws or a clip and connects to a 2-wire harness
• Handle the connector and wiring carefully; route and secure away from hot or moving parts
• After installation, clear stored errors and run a test cycle to proper readings

This fan cover protects the appliance's blower assembly and directs airflow to maintain proper ventilation. It helps prevent debris from reaching the fan and supports efficient air movement for reliable operation. What it does:

• Shields the blower/fan from dust, lint, and loose debris that can interfere with airflow
• Directs and channels airflow for consistent ventilation and cooling of internal components
• Helps reduce noise by enclosing the fan area and stabilizing the blower assembly
• Commonly replaced when cracked, damaged, or warped after impact or wear

• One fan cover

• Inspect surrounding seals and mounting tabs before installation; replace any broken clips
• Power off and disconnect the appliance before accessing internal components
• May require basic tools (screwdriver, socket) and removal of adjacent panels for access

This Broil Heating Element is an OEM part for Bosch Ranges. It is responsible for providing high heat for broiling functions and evenly distributing heat within the oven cavity. It ensures efficient broiling performance for cooking various dishes.

A common issue with a malfunctioning Broil Heating Element is wear and tear over time, leading to potential element damage or failure. Frequent usage, or heating irregularities can compromise its function.

Symptoms of a defective Broil Heating Element may include:

• Uneven broiling or cooking results
• Inadequate heating or failure to reach desired temperatures
• Visible damage or signs of wear on the heating element

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation