Parts for Kenmore 796.71522210 (79671522210, 796 71522210): Cabinet And Door Assembly Parts

This cabinet cover assembly replaces the dryer or washer top cabinet panel to restore the appliance's exterior protection and clean appearance. It provides a secure, factory-style fit for the machine's top section. What it does:

• Covers and protects internal components under the top of the cabinet from dust and debris
• Restores the appliance's finished appearance after damage or corrosion to the top panel
• Helps maintain proper airflow and sealing around the top area when installed correctly
• Compatible where OEM part ACQ75450501 is specified

• Installer level: moderate; basic disassembly of the appliance top may be required
• Disconnect power and, if applicable, water before starting work
• Keep mounting hardware and clips from the original panel; use only confirmed OEM fasteners

Note: May be able to use Whirlpool latch kit# 279570.

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

A replacement latch body that secures the appliance door and helps ensure a proper, reliable seal. Restores correct door engagement so cycles can start and run safely. What it does

• Provides the main latch mechanism that holds the door closed during operation.
• Ensures the door stays firmly engaged to maintain a proper seal and safe operation.
• Can prevent the appliance from starting or completing cycles if the door won't stay latched.
• Common symptom linkage: door won't stay closed, door feels loose, or appliance fails to start because the door won't engage.

• Disconnect power (and water, if applicable) before beginning any repair.
• Access may require removing the door trim or front panel; follow the appliance's service instructions.
• Handle sharp edges and small fasteners carefully; keep removed screws in a labeled container.
• Test door engagement and run a short cycle after installation to ensure proper operation.

This cabinet hole cap plugs unused hinge or screw openings on the dryer cabinet. It restores a clean, finished look and helps keep lint and moisture out after a door reversal or service. What it does:

• Covers open hinge/screw holes on the dryer cabinet
• Helps block lint, dust, and moisture from entering through unused openings
• Restores a finished appearance; helps prevent snags around exposed holes
• Commonly replaced when a cap is missing, cracked, or loose

• 1 cabinet hole cap

• Disconnect power before working near the cabinet
• Remove any damaged cap and clean the opening
• Press the new cap into the hole until fully seated and flush
• Wear gloves; cabinet edges and holes can be sharp

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This power cord assembly supplies AC power to the appliance and restores safe operation after a damaged or faulty cord. It replaces the worn or frayed factory cord so the appliance can power on reliably. What it does

• Provides the main AC connection between the appliance and household power
• Replaces cords with visible damage, exposed wiring, burnt connectors, or intermittent power
• Helps stop arcing, sparking, or overheating caused by a failing cord
• Fits into the appliance's cord terminal block for a direct, plug-in power connection

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Tighten all terminal screws securely and route the cord away from sharp edges and moving parts

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.