Parts for Ge GSD1236T62WW: 02 - Section2 Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Prevents water leaks at the dishwasher door corners during wash cycles. Replace if you notice leaking along the bottom of the door. Clips onto tub rail.

Rubber baffle prevents leaks at dishwasher tub corner. Replace if worn, cracked, or causing water leakage during wash cycles. Snap-fit design.

Replacement mounting screw for securing handles, panels, and internal components. Needed when original screws are stripped, lost, or broken during repairs.

Door won't close or latch properly? This latch keeper secures the door strike so your dishwasher stays closed during cycles. Quick DIY repair.

Size: 10-24 x 1/2 inch.

Replacement leveling screw threads into your dishwasher's leveling leg to adjust cabinet height. Install when original is stripped, damaged, or missing.

Dishes not drying or wet after cycle? The heating element heats air during drying. Simple DIY repair with video guide, typically under 30 minutes.

This is a replacement mounting nut that secures components to their mating studs or shafts, restoring proper fit and preventing looseness that can cause noise or misalignment. Use it to replace a worn, stripped, or missing nut. What it does:

• Fastens parts to studs or shafts to keep assemblies secure and aligned.
• Prevents wobbling, rattling, and reduced performance caused by a loose or missing nut.
• Restores reliable mechanical connection after thread damage or corrosion.
• Works where a standard hex-style fastening nut is required by the OEM design.

• One replacement mounting nut.

• Disconnect power and unplug the appliance before beginning work.
• Verify correct stud engagement and thread direction before tightening.
• Use the proper-sized wrench and tighten to the manufacturer's recommended torque; avoid over-tightening to prevent thread damage.
• If threads are damaged, replace the mating stud or use an approved repair kit—do not force a nut onto stripped threads.

Dishwasher bag hugger assembly installs on upper rack to secure lightweight items during wash cycles. Replace if broken, cracked, or missing.

Fix dishwasher overfilling or not filling properly with a new float dome. Protects the float sensor for accurate water level control. Easy 15-minute repair.

Fix dishwasher overflows or underfilling with a new water level float. This part regulates filling by rising with water to signal the switch.

Guides the dishwasher float and connects it to the switch mechanism. Replace if cracked, broken, or worn to restore proper water level control.

Replacement bracket that secures the flood switch in your dishwasher. Holds the leak detection switch in proper position. Needed when bracket is cracked or broken.

Seal washer that sits between the dishwasher pump and motor assembly. Replace if cracked, deteriorated, or causing leaks beneath the pump housing.

Dishwasher overflowing or not filling? This float switch detects water levels to prevent overflow and control filling. DIY-friendly repair part.

Dishwasher not powering on or experiencing electrical issues? This terminal block housing insulator protects wire connections. Simple repair part.

Protective cover that sits over your dishwasher's pump inlet to screen debris. Replace if cracked, broken, or missing to protect internal components.

Fix dishwasher leaks or poor cleaning with a new sump cap. Seals the sump opening to contain wash water and protect the pump. Quick DIY replacement.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fix a dishwasher that won't drain completely with this piston and nut valve assembly. Simple DIY repair when water remains in tub after cycles.

Replaces broken or cracked 3rd level spray arm assembly that mounts at the top of the tub. Includes mounting tabs and collar for secure installation.

Used to supply water to the upper spray washarm.

Replacement upper dishrack for dishwashers. Installs in the top position to hold plates, bowls, and glasses. Replace if rusted, cracked, or broken.

Replacement slide rail for dishwasher upper rack. Installs on cabinet wall to guide rack in and out. Needed when original is bent, twisted, or broken.

Secures the end of the dishwasher rack slide rail. Replace if cracked, broken, or missing to prevent racks from sliding off track or misaligning.

Upper rack roller assembly for dishwashers. Mounts to the liner to guide the upper rack smoothly in and out. Replace if cracked, worn, or broken. Screws included.

Replacement roller and stud assembly for dishwasher racks. Installs on upper or lower rack to restore smooth gliding. Needed when rollers crack or studs break.

Lower dishrack assembly for dishwasher bottom level. Holds plates, pots, and pans during wash cycles. Replace if rusted, cracked, or tines broken.

Replace broken or missing lower dishrack rollers and axles. Attaches to the bottom rack for smooth gliding when loading dishes. Sold as one roller kit.

Replacement roller and axle kit for dishwasher lower racks. Includes 8 wheels and 8 axles. Replace when rollers are broken, cracked, or missing.

Connects door handle to latch assembly and counterbalance springs. Replace if cable is frayed, snapped, or damaged, preventing proper door operation.

This part has been discontinued and is no longer available.

Dishwasher not filling with water or leaking during cycles? The water inlet valve controls water flow. DIY-friendly repair, typically 10-30 minutes.

Replacement mounting screw for dishwashers and electric ranges. Secures panels, covers, and internal components. Order when original is missing or stripped.

Replacement silverware basket with handle for your dishwasher. Needed when original basket is cracked, broken, or has worn holes that let utensils fall through.

Specs: 10 - 32 t hex 7/16 s

Routes water from inlet valve to tub. Replace if cracked, leaking at connections, or worn from age. Installs between valve and tub exterior connection point.

Dishwasher not filling with water or leaking during cycles? The water inlet valve controls water flow. DIY-friendly repair, typically 10-30 minutes.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Replacement mounting screw for dishwashers. Secures panels, brackets, or components inside the unit. Needed when original screws are stripped or missing.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.