Parts for Lg LFX25974ST/04: Dispenser Parts

The LG Refrigerator Water Filter is an OEM Replacement Part. It is designed to improve the quality of water and protect refrigerators and ice machines from sediment deposits. This NSF-Certified filter effectively reduces iron and particulates. It also preserves beneficial minerals like fluoride. The filter measures 5.6 inches high and 3.3 inches in diameter.

It is installed by removing the top shelf and pulling the old filter downward. Then turn it counter-clockwise, and replace it with the new filter aligned in a horizontal position. To ensure the best performance and the removal of trapped air and contaminants, it's recommended to flush the dispenser with 2.5 gallons of water in alternating cycles. If your model includes a water filter indicator, press and hold the Filter or Reset button for 5 seconds after installation. With a lifespan of 6 months and a 500-gallon capacity, this filter provides both quality and longevity.

This ice dispenser door assembly opens to release ice and seals the chute when not in use. Replacing a worn flap restores a tight seal to reduce frost buildup and air leaks at the dispenser.

• Seals the ice chute to keep warm air out and cold air in
• Opens during dispensing to allow cubed or crushed ice to pass
• Helps prevent frost/ice accumulation in the chute and around the dispenser
• Common signs of failure: flap won't open/close, visible gap or draft at the chute, frost forming in the dispenser area

• Always disconnect power before servicing the dispenser
• Remove dispenser trim/control panel as directed; disconnect wiring as needed
• Remove mounting screws/clips, swap the assembly in the same orientation, and reuse existing hardware if applicable
• Restore power and test for smooth operation and a proper seal

This dispenser door link connects the dispenser actuator to the refrigerator dispenser door so the door opens and closes smoothly when dispensing. Replaces a worn or broken link to restore proper dispenser door movement. What it does:

• Transfers motion from the dispenser actuator to the dispenser door so the door opens when dispensing
• Keeps the dispenser door aligned for proper sealing and closure
• Can fail if the door won't open, sticks, or the dispenser lever feels loose or disconnected
• Compatible with dispenser assemblies that use a separate plastic/metal link between actuator and door

• Disconnect power to the appliance before starting any work
• Access may require removing the dispenser trim or front housing—keep fasteners organized
• Handle plastic components carefully to avoid cracking; inspect surrounding parts for wear

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

The Ice Door Lever Spring is an OEM component compatible with LG refrigerators. It is part of the mechanism that opens and closes the ice door on LG French door refrigerators. Over time, springs can lose resiliency or become misaligned.

Causes may be extensive usage over years or damage like kinking that compromises spring function.

Symptoms of a bad ice door lever spring include:

• The ice door not latching fully when closed
• Difficulty opening or poor balance while moving the door
• The lever rubbing or catching instead of moving smoothly

This OEM LG part is also compatible with Sears/Kenmore side-by-side refrigerators.

This molded plastic funnel directs water inside the appliance to prevent leaks and pooling and helps ensure proper drainage or water delivery. It replaces a damaged or missing funnel to restore correct internal water flow. What it does:

• Channels water from the supply or inlet to the drain or reservoir to prevent overflow
• Helps stop water pooling that can cause leaks or internal water damage
• Restores proper routing when cracked, warped, or broken
• Commonly linked to symptoms like leaks under the unit, water pooling inside compartments, or disrupted ice/water delivery

• One molded plastic funnel

• Disconnect power and shut off the water supply before starting repair
• Inspect mounting tabs and surrounding seals; replace any damaged fasteners or gaskets
• Typically installs by aligning and snapping into place or securing with existing screws — avoid forcing to prevent breakage

This dispenser lever replaces a cracked, loose, or non-returning dispenser paddle so you can reliably activate the fridge dispenser again. Durable replacement that restores normal button/paddle operation and user control. What it does:

• Acts as the user-operated paddle that presses the dispenser switch to release water or ice
• Restores proper lever return and consistent contact with the dispenser switch
• Stops leaks, wobble, or snagging caused by a broken or worn paddle
• Helps eliminate intermittent or failed dispenser activation related to a damaged lever

• One dispenser lever

• Disconnect power to the appliance before starting; shut off the water supply if working near the dispenser
• Remove dispenser bezel/trim and any inner cover per manufacturer instructions to access the lever
• Replace the lever and confirm it moves freely and properly contacts the dispenser switch before reassembling

This display cover is the clear protective lens that fits over the appliance control panel, restoring a clean appearance and protecting the underlying display and buttons from dirt, spills and wear. What it does

• Protects the control board and display from splashes, grease and daily wear.
• Keeps touchpads and button legends visible and readable.
• Helps maintain a finished, factory look for the control panel.
• Replaces a cracked, scratched or discolored lens that affects appearance or usability.

• One display cover (control panel lens)

• Disconnect power to the appliance before starting any work.
• Remove any trim or bezels covering the control panel as required to access the lens.
• Handle the lens carefully to avoid scratches; use a soft cloth and appropriate fasteners.

This display cover assembly protects the control panel and display while keeping the appliance looking finished. It restores a clean, readable interface and shields buttons and indicators from spills and wear. What it does

• Replaces a cracked, scratched, or discolored display cover to improve appearance and readability
• Protects the underlying display and control electronics from dust and light contact damage
• Helps maintain button alignment and prevents debris from entering the control area
• Returns the front panel to a factory-finish look after accidental damage

• Disconnect the appliance from power before starting any repair to avoid shock or damage
• Minor disassembly of the control panel is typically required; keep screws and clips organized
• Inspect mounting tabs and clips for damage; replace any broken fasteners to ensure a secure fit

This replacement lever button is the user-operated push control that lets you engage the appliance's latch or control function. It restores a worn, cracked, or non-springing button so controls respond reliably. What it does

• Acts as the external push/lever used to latch, unlatch, or activate a control mechanism
• Replaces cracked, loose, or unresponsive buttons that no longer engage properly
• Helps restore normal tactile response and alignment of the control assembly
• Works with the existing actuator and mounting points — no modification required

• One replacement lever button

• High-level replacement only; remove power source before starting repair
• Handle panels and clips gently to avoid damage to trim or surrounding controls
• Verify correct button orientation before final reassembly

The Dispenser Switch is an OEM part for LG refrigerators. It is responsible for controlling the operation of the dispenser, allowing you to dispense water or ice from the refrigerator door. This switch is located in the dispenser house and activates the dispenser when pressed.

Causes of a bad dispenser switch can include wear and tear over time, electrical malfunctions, or damage due to accidental mishandling or impact.

Symptoms of a bad dispenser switch include:

• Inability to dispense water or ice when pressing the buttons.
• The dispenser works intermittently. 
• No response or delayed response when pressing the dispenser buttons.

This LG part can also be used on Kenmore/Sears appliances. 

This DC motor powers the washer's drum rotation, restoring normal spin and agitation so loads wash and rinse effectively. Designed to replace a worn or failed drive motor for reliable drum movement and consistent cycle performance. What it does:

• Spins the drum and controls agitation for wash and rinse cycles
• Restores normal spinning when the washer won't agitate or spin
• Helps reduce noisy, uneven, or intermittent drum rotation when the motor is the cause
• Works with the washer's electronic controls to regulate motor speed and direction

• One DC drive motor

• Disconnect power before starting and follow the washer manufacturer's service manual
• Basic disassembly of the cabinet and drum support is typically required; keep fasteners organized
• Verify wiring connectors and mounting orientation match the removed motor before final assembly
• Check control board and wiring for faults