Parts for Maytag MGD8630HC3: Door Parts

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

This door assembly replaces a damaged or worn refrigerator door to restore proper closure and appearance. It provides the outer structure and mounting surface needed for seals, handles, and interior components to function correctly. What it does:

• Replaces a cracked, dented, or bent door to maintain a tight seal and correct alignment
• Restores exterior appearance and provides mounting for handles, hinges, and inner liners
• Helps prevent cold air loss that can cause higher energy use or spoiled food
• Works when original door is warped, has impact damage, or cannot hold gasket securely

• One complete door assembly

• Requires basic appliance repair skills; may need two people for safe handling and alignment
• Keep power disconnected and remove food items from door before starting work
• Handle edges and glass carefully to avoid injury or further damage
• Tighten hinges and hardware to manufacturer torque; check door seal and alignment after installation

This genuine mounting screw secures panels and components so assemblies stay aligned and rattle-free. Designed to replace worn or missing fasteners and restore proper fit and function. What it does:

• Secures panels, brackets or trim to prevent movement and vibration
• Restores proper alignment of assemblies that feel loose or shift
• Helps eliminate rattling, squeaks, or parts that fall away during use
• Matches OEM thread and head type for correct fit

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Replace any additional damaged or missing fasteners for best results
• Disconnect power or follow appliance-specific safety steps before working near wiring or energized components

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Window is an OEM part for Whirlpool dryers. It forms the inner layer of the dryer door, providing insulation and protection to the contents inside the dryer drum. This inner window ensures a clear view of the drying process while preventing heat loss and potential damage to the outer door.

A bad door inner window can occur due to accidental impact, wear and tear, or improper handling. If you notice symptoms such as cracks, fogging, or damage to the inner window, it may be time to replace this part.

Symptoms of a bad door inner window include:

• Visible cracks or damage
• Fogging or cloudiness
• Compromised insulation

Restore your Whirlpool dryer by replacing the faulty or damaged door inner window with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Hinge is an OEM replacement part for Whirlpool dryers. Responsible for securely attaching the dryer door, these hinges play a vital role in usability. Proper functioning of the hinge is crucial for maintaining the door’s alignment and ensuring it closes tightly to retain heat during the drying cycles.

Causes of a bad hinge can include normal wear and tear over prolonged use cycles. Excess weight or strain on the door from heavy loads could damage hinge components over time.

Symptoms of a bad hinge include:

• Loose or sagging door that does not close flush
• Difficulty opening or closing the dryer door
• Noisy squeaks or squeals coming from the hinge area

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

The Washer/Dryer Door Hinge is an OEM replacement part for Whirlpool washer and dryer units. It is a component that allows the appliance door to open and close smoothly while providing a secure attachment point to the main cabinet.

Symptoms of a bad washer/dryer door hinge:

• Difficulty in opening or closing the door
• Door sagging or not aligning correctly when closed
• Excessive noise or rattling when the door is opened or closed
• Water leaks or air leaks around the door area

Causes of a bad door hinge can include mechanical wear and tear over time, physical damage due to impact or mishandling, or improper installation or alignment of the hinge components.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer and dryer models.

The Hinge Pin Bushing is an OEM part designed for Whirlpool washing machines that is responsible for providing a pivot point for the hinge pin and ensuring the door opens and closes smoothly and securely. Over time, this bushing can wear out or become damaged, leading to issues with the door's alignment and opening.

Symptoms of a bad Hinge Pin Bushing include:

• Difficulty in opening or closing the door
• Noise when the door is moved
• Loose or wobbly door 
• The door not staying closed

Causes of a bad hinge pin bushing can range from normal wear and tear to excessive force used on the door or lid. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This bumper cushion reduces vibration and cushions contact points to protect surfaces and quiet operation. It restores proper spacing and prevents metal-to-metal contact on compatible appliances. What it does:

• Cushions doors, drawers or panels to prevent rattling and wear
• Absorbs shock to reduce noise during cycles or movement
• Helps maintain proper alignment and spacing of components
• Prevents scratches and protects finishes where parts meet

• Disconnect power before accessing internal parts or removing panels
• Remove the old bumper and press the new bumper into the same mounting location (no special tools usually required)
• Replace with like-for-like bumper; do not modify part or mounting to avoid fit issues
• If adhesive is used, follow OEM guidance and allow proper curing time before use