Parts for Ge CZS25TSEBFSS: Fresh Food Section Parts

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

Front mounting grommet.

This replacement screw secures refrigerator panels, brackets, and trim to help keep components aligned and quiet. It matches the specified #8-18 thread and 1-1/2 inch length used at designated mounting points.

• Fastens panels, brackets, covers, and hardware as designed by the manufacturer
• Restores a missing or damaged fastener to keep parts secure and aligned
• Correct #8-18 tapping thread and 1-1/2 in. length for specified locations

• Unplug the refrigerator or disconnect power before servicing
• Wear cut-resistant gloves to protect from sharp edges
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any model-specific washers or clips originally installed on your unit

This rubber grommet secures the appliance's base grille, helping keep the grille fitted and reducing vibration and rattle. It's a simple replacement part to restore a snug, finished look at the appliance base. What it does:

• Cushions and retains the base grille in place to prevent gaps and movement
• Helps reduce vibration noise and rattling from a loose grille
• Restores proper fit where a grommet is cracked, torn, or missing

• One (1) grommet for the base grille

• Disconnect power to the appliance before beginning any service
• Typically installs by pressing into the grille or cabinet opening—no special tools required
• Inspect surrounding grille tabs or mounting points and replace any damaged hardware as needed

This dial pan chill is the replacement temperature control pan that mounts behind the fridge control knob to secure and position the chilling temperature dial. Restores proper knob fit and reliable access to temperature adjustments. What it does:

• Holds and centers the temperature control dial so the knob turns smoothly
• Keeps the control assembly stable to prevent slipping or misalignment
• Helps maintain clear user access to temperature settings
• Commonly replaces cracked, warped, or broken pans that cause loose or off-center knobs

• Basic hand tools may be required; handle with care to avoid damaging adjacent trim
• Power off or unplug the appliance before starting any repair
• Inspect the control knob and shaft for wear when replacing the pan; replace worn components as needed

This small replacement linkage secures and positions the pan-chill assembly in compatible refrigerators, helping keep the drain/collector aligned and reducing movement or vibration. Replace a broken link to restore stable pan alignment. What it does:

• Connects and secures the pan-chill (drain/collector) assembly to the fridge framework
• Keeps the pan aligned for proper drainage and to prevent water pooling
• Reduces rattling or movement caused by a cracked or worn linkage
• Helps maintain correct spacing so adjacent components fit and operate without interference

• One linkage pan-chill mounting link

• Disconnect power to the appliance before starting work
• Access may require removing interior panels or shelving—keep fasteners organized
• Install by aligning the linkage with mating tabs and snapping or fastening into place; do not force broken plastic

This replacement chill pan collects defrost and condensation water and channels it away so your refrigerator interior stays dry and free of pooled water. Designed to restore normal drainage and reduce leaks. What it does:

• Collects defrost and condensation water from the evaporator area
• Directs water to the evaporator/condenser area to evaporate safely
• Helps prevent water pooling inside the fresh-food or freezer compartment
• Can reduce musty odors caused by standing water and trapped debris

• Disconnect power to the appliance before beginning any service
• Empty the compartment and remove any components blocking access
• Inspect and clean the drain tube and mounting points when replacing the pan
• Use OEM instructions for fitment and reassembly

This replacement knob fits the temperature control on the refrigerator's chill/deli/snack pan. It restores your ability to adjust airflow to the drawer so you can set the pan to a colder or warmer setting when the original knob is broken or missing. What it does:

• Attaches to the chill/deli pan temperature control to regulate cold-air flow into the drawer
• Restores user control of the drawer's colder/warmer setting
• Typical symptoms include a cracked or missing knob, a knob that won't stay on, or slipping/stripped engagement
• May help if the drawer setting can't be adjusted because the knob is damaged

• 1 control knob

• Unplug the refrigerator before servicing
• Remove the deli/snack pan for access to the control shaft
• Align the knob with the shaft and press on firmly until fully seated
• Reinstall the pan and restore power; verify the control turns smoothly

The Temperature Sensor is an OEM replacement part for GE refrigerators, designed to accurately monitor and relay the temperature inside the refrigerator and freezer compartments to the electronic control board. By detecting the slightest changes in internal temperature, the sensor allows the control board to make real-time adjustments to the cooling system, activating the compressor and fans as needed to maintain optimal conditions for food preservation.

Over time, the temperature sensor can fail due to electrical issues, exposure to moisture, or general wear and tear. A malfunctioning sensor can lead to improper temperature regulation, affecting the efficiency of the refrigerator and the freshness of stored food.

Symptoms of a bad Temperature Sensor include:

• The refrigerator or freezer not maintaining the set temperature 
• The appliance running continuously or more frequently than normal
• Inaccurate temperature readings displayed  

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This LED light cover protects and diffuses the refrigerator's interior LED lighting, improving light distribution while shielding the lamp from spills and impact. It restores a finished appearance and prevents direct glare from exposed LEDs. What it does:

• Diffuses and softens interior LED light for even illumination.
• Protects the LED module from splashes, dust, and accidental contact.
• Helps prevent direct glare from exposed bulbs for clearer visibility.
• Replaces cracked, yellowed, or missing covers that affect light quality.

• One LED light cover.

• Disconnect power to the appliance before removing or installing parts to avoid shock.
• Typically snaps into place or secures with a small screw; handle gently to avoid cracking.
• Inspect mounting tabs and nearby lamp housing for damage; replace any broken hardware before reinstalling.
• Use gloves or a clean cloth to avoid fingerprints or scratches on the diffuser.

This pan extension secures and positions the refrigerator's LED light assembly to illuminate the fresh-food compartment for better visibility. It replaces a cracked, loose or missing light pan extension to restore proper light placement. What it does:

• Provides a mounting surface and trim for the interior LED light assembly
• Helps direct and protect the LED module and wiring from moisture and debris
• Restores stable, aligned lighting when the original pan is cracked, broken, or loose
• Reduces rattling or movement of the LED assembly that can cause intermittent lighting

• Disconnect power to the appliance before beginning any work
• Access usually requires removing interior shelves and light cover; keep fasteners for reuse
• Handle plastic trim and LED module carefully to avoid damage

This bottom hinge pin supports and serves as the pivot for the refrigerator door. An accurate, tight-fitting hinge pin helps the door swing smoothly and seal properly to maintain temperature and reduce wear.

• Serves as the lower pivot point for the door on the bottom hinge
• Helps keep the door aligned for proper closing and gasket contact
• Replacing a worn pin can improve door movement and reduce stress on the hinge

• Unplug the appliance before servicing
• Support the door to relieve weight from the hinge before removing hardware
• Transfer any spacers/shims in their original order to maintain alignment
• Tighten fasteners securely and check door swing and seal after installation

LED light board assembly that provides interior illumination for compatible refrigerators. Replaces a failed or dim LED module to restore even lighting so you can see contents clearly and access food safely. What it does:

• Replaces the refrigerator's interior LED light board to restore proper illumination.
• Fixes common lighting symptoms such as no light, dim lights, flickering, or partial outages.
• Provides a direct replacement that mounts in the existing light housing and connects to the factory wiring harness.

• Disconnect power (unplug or shut off breaker) before starting work to avoid electric shock.
• Remove interior shelves or light cover as needed; handle the board by its edges and avoid touching LED surfaces.
• Verify connector orientation and seat wiring harness fully; secure board to the housing with original fasteners.

This bottom door hinge supports the refrigerator door and serves as the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and sealing to help prevent door sagging and cooling loss. What it does:

• Supports the door's weight at the lower corner and maintains alignment
• Provides the pivot for opening/closing and reduces friction at the door base
• Wear can cause door sagging, rubbing/binding, or the door not closing fully
• Misalignment may lead to poor gasket contact, warm spots, or condensation/frost near the door

• 1 bottom door hinge

• Disconnect power and, if applicable, shut off water before starting
• Remove items from the door and have a helper support it during removal
• Remove the upper hinge to lift the door off the lower hinge; retain any shims/spacers
• Swap the hinge, transfer shims as found, align the door, tighten fasteners, and verify the gasket seals all around

The Light Switch is an OEM part for GE refrigerators. It controls the refrigerator's interior light, turning it on when the door is opened and off when the door is closed. This ensures energy efficiency and convenience, illuminating the refrigerator's interior for easy visibility while searching for items.

Causes of a bad light switch include mechanical wear from constant use, damage from an impact, or electrical issues.

Symptoms of a bad Light Switch include:

• The interior light does not turn on when the refrigerator door is opened
• The light stays on when the door is closed, potentially leading to overheating or melted plastic components in the light housing area
• Intermittent functioning of the light, indicating a loose or damaged switch

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Keep water and ice flowing without internal filtration. This MSWF water filter bypass plug replaces the filter to seal the housing and route water properly to the dispenser and ice maker when a filter is not used.

• Installs in place of the MSWF filter to bypass filtration
• Maintains water flow to the dispenser and ice maker with no filter installed
• Helpful for troubleshooting restricted flow or when using an external filtration system
• Seals the filter head to help prevent leaks during bypass
• Note: No water is filtered while this plug is installed

• Shut off the water supply and dispense water to relieve system pressure
• Remove the MSWF filter; align and twist the bypass plug to lock into the filter head
• Restore water, check for leaks, and run the dispenser briefly to purge air
• Follow your refrigerator's instructions and use appropriate hand/eye protection

This water filter manifold assembly holds the MSWF cartridge and routes water through the refrigerator's filtration system to the dispenser and icemaker. Replacing a damaged filter head restores a secure seal and consistent water flow.

• Provides the twist-lock mount and seal for the MSWF filter cartridge
• Connects inlet and outlet lines to direct filtered water to the dispenser and icemaker
• Common failure symptoms: leaks around the filter head, low or no dispenser flow, icemaker not filling, or the filter not seating/locking properly
• Designed specifically for refrigerators that use the MSWF filter style

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Remove the MSWF filter; transfer mounting hardware and line connections to the new assembly one at a time to maintain orientation
• Restore water and power; check all connections for leaks and run water to purge air from the system

This foam insulation for the refrigerator manifold helps reduce heat transfer and condensation around the refrigerant/water manifold, improving temperature stability and preventing unwanted frost buildup in the cabinet area. What it does:

• Wraps and insulates the refrigerator manifold and nearby tubing to limit heat gain and condensation
• Helps maintain consistent cooling performance by reducing thermal interference with the manifold
• Reduces risk of localized frost or moisture buildup that can affect nearby components
• Be needed if existing insulation is torn, compressed, missing, or water-damaged

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove shelves, panels, or drawers as needed for access; keep track of fasteners
• Replace damaged insulation carefully to ensure full coverage of the manifold and tubing; trim if necessary for a snug fit
• If adhesive backing is present, press firmly to secure; do not block airflow or pinch tubing

This water filter cover protects and secures the refrigerator's inline filter assembly while keeping the filter compartment sealed and tidy. It helps ensure a proper fit so the filter can seat correctly and water flows as intended. What it does:

• Replaces a cracked, broken or missing water filter cover to restore proper filter seating and alignment
• Helps prevent leaks by maintaining the cover seal around the filter area
• Keeps the filter compartment clean and prevents debris from entering the housing
• Supports correct water flow and helps avoid dispensing problems caused by a loose or damaged cover

• One water filter cover

• Disconnect power and turn off the refrigerator water supply before servicing
• Remove the old cover and gently snap or screw this cover into place per your model's mounting points
• Hand-tighten fasteners; do not overtighten plastic clips or screws
• After installation, restore power and water, check for leaks, and run a few cycles to confirm proper seating

The Evaporator Drip Pan is an OEM part for GE refrigerators. This pan collects condensation and defrost water, preventing leaks and water damage to your kitchen floors.  

Causes for replacement often stem from physical damage, such as cracks or holes that allow water to leak out. Over time, the drip pan may also become brittle and more susceptible to damage due to the constant exposure to moisture and temperature fluctuations. 

Symptoms of a bad Evaporator Drip Pan include:

• Water accumulation under or around the refrigerator
• Mold or mildew smell coming from beneath the refrigerator
• Overflowing, indicating a crack or hole in the pan

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Fresh Food Lever Assembly is an OEM part for GE refrigerators. It plays a crucial role in the operation of the refrigerator, enabling the smooth adjustment of settings within the fresh food compartment. This lever assembly is responsible for the user's ability to fine-tune the temperature and humidity levels, ensuring that the food stored inside remains fresh and well-preserved. For the same part in white, purchase WR11X10007.

Over time, the lever assembly may become worn or damaged due to regular use, accidental impacts, or environmental factors such as extreme temperatures or humidity.

Symptoms of a bad Fresh Food Lever Assembly include:

• Difficulty in adjusting the temperature or humidity settings.
• The lever becoming loose or unresponsive.
• Inconsistent temperature control within the fresh food compartment.
• Increased energy consumption as the refrigerator works harder to maintain settings.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Closure Spring is an OEM replacement part for GE refrigerators. It provides balanced tension to assist the door hinges and latch mechanism in securely closing the refrigerator door. The spring helps the door shut fully while preventing it from slamming closed abruptly.  

Symptoms of a bad door closure spring include:

• The door not latching securely or remaining slightly ajar    
• Difficulty closing the door fully without assistance
• Increased thermal loss as the door does not seal tightly
• Risk of food items falling out from an open door position   

Causes of failure include metal fatigue from prolonged use. Springs can also weaken from mineral buildup over many years of repeated openings and closings. 

This OEM GE replacement spring is also compatible with models including GE, Monogram, and select Kenmore units.