Parts for Ge PGB945SEF2SS: Gas & Burner Parts

This LP conversion kit converts a compatible gas range/oven from natural gas to liquid propane, supplying the correct fuel orifices and components needed for safe LP operation when installed per manufacturer instructions. What it does:

• Replaces orifice and regulator components used to adapt the appliance for propane fuel
• Ensures correct fuel flow and burner operation after switching to LP
• Helps address improper burner flames or ignition issues caused by incorrect fuel orifice sizing
• Required when changing the appliance fuel type to meet safe operating specifications

• LP conversion components required for conversion

• Turn off gas supply and power before starting; follow OEM conversion instructions exactly
• After installation, perform a thorough leak test and verify proper burner flames and operation
• Retain OEM documentation and apply any required fuel-type labeling to the appliance

The Knob Assembly is an OEM part for GE ranges. This part allows users to control and adjust the temperature settings of the appliance.

Causes of a bad Knob Assembly can range from physical damage or impact to internal mechanical wear over extended use. 

Symptoms of a faulty Knob Assembly include:

• Difficulty turning or rotating the knob
• Knob feeling loose or wobbly
• Inconsistent temperature control or inaccurate settings
• Knob becoming detached or falling off

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 8 - 32 inch.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

LP orifice spud that meters propane to a single burner for correct flame size and efficient combustion after converting a cooktop or oven to LP. Restores proper burner performance and safer operation. What it does:

• Meters propane flow to one burner to establish the correct flame for LP fuel.
• Used when converting a range or oven from natural gas to propane (LP).
• Helps correct flames that are too large, yellow, uneven, or won't stay lit.
• Replaces a worn, damaged, or incorrect LP orifice spud for improved burner control.

• Shut off the gas supply at the appliance and service valve before servicing.
• Follow OEM conversion instructions.
• After installation, check all gas connections for leaks with an approved method; do not operate the appliance if you detect a gas leak.
• Use only the exact orifice specified for LP conversion—do not substitute unverified parts.

This LP orifice spud meters propane to a burner on compatible gas ranges/cooktops. Replacing a clogged, damaged, or incorrect spud helps restore proper flame size and consistent burner performance after conversion or service. What it does:

• Threads into the gas system to control LP gas flow to the burner
• Corrects flame characteristics after LP conversion when the proper size is used
• Common symptoms of a wrong/failed spud: yellow-tipped flames, flames too high/low, uneven heating, poor simmering
• Helps maintain stable blue flames for efficient combustion on LP

• 1 LP orifice spud

• For LP (propane) use only; do not use with natural gas
• Turn off gas supply and power before servicing; allow the appliance to cool
• Match each burner position to the specified orifice per your model's conversion chart; tighten snugly without overtightening
• After installation, leak-check with a soap solution and verify flame characteristics per the manual

A replacement burner valve cover that protects and conceals the gas valve assembly on compatible ranges, helping keep valve components clear of spills and debris for more reliable burner operation. What it does:

• Covers and protects the gas valve area from food, moisture and spills.
• Helps prevent debris from interfering with valve knobs and internal valve parts.
• Can reduce intermittent ignition or burner performance issues caused by contamination.
• Restores the finished appearance around the valve for safer, cleaner operation.

• Always shut off the gas supply and unplug the appliance before servicing.
• Use basic hand tools; handle the valve area gently to avoid disturbing fittings or tubing.
• After installation, check for gas leaks with a soapy-water solution or a proper leak detector—do not use an open flame.

This orifice holder secures the burner orifice for the right-rear cooktop burner, keeping the gas orifice aligned for consistent ignition and flame. It helps restore proper burner performance when the holder is damaged or missing. What it does:

• Holds and positions the gas orifice for the right-rear burner so fuel flows through the correct opening
• Helps maintain a steady, even flame and reliable ignition at the right-rear burner
• Commonly replaced when the burner won't light, has weak or uneven flames, or when the holder is cracked or corroded
• Designed to mate with the burner tube and orifice for proper gas flow

• Turn off gas supply and power to the appliance before beginning any service
• Remove burner cap and assembly to access the orifice holder; use appropriate hand tools and avoid overtightening
• Inspect the orifice and any sealing gaskets for damage; replace damaged orifices or gaskets as needed

This bake burner is the oven's primary gas burner assembly that produces and directs heat for baking and roasting. Replaces a worn or damaged burner to restore consistent oven heat and cooking performance. What it does:

• Provides the main heat source for the oven cavity during bake/roast cycles.
• Directs and distributes the gas flame along the oven floor for even cooking.
• Works with the oven igniter and gas valve to light and maintain the flame.
• Common symptom link: oven won't reach temperature, won't heat, or heats unevenly.

• Disconnect power and shut off the gas supply before attempting service.
• Inspect and match mounting points and gas connection; handle the burner to avoid bending or damaging flame ports.
• Replace only with the correct OEM part number; check igniter and valve if issues persist.

The Igniter Mounting Screw is an OEM replacement part for GE ovens and ranges. This screw secures the igniter to the burner assembly, ensuring it remains firmly in place for consistent and reliable ignition. Its precise fit and durable design help maintain the stability and functionality of the igniter.

Over time, mounting screws can become corroded, stripped, or lost during repairs or maintenance. A missing or damaged screw may result in a loose igniter, affecting the appliance's ability to ignite properly.

Symptoms of a bad or missing igniter mounting screw include:

• The igniter becoming loose or misaligned

• Difficulty securing the igniter during installation or repair
• The burner fails to ignite reliably or consistently
• Increased noise or movement of the igniter during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This igniter cover is a replacement protective shield that helps protect the oven igniter from food spills and debris, extending the igniter's service life and helping the burner ignite reliably. What it does:

• Shields the oven igniter from direct contact with spills, drips and falling debris
• Helps prevent premature igniter damage that can lead to ignition problems
• Can reduce the chance of shorting or erratic ignition caused by contamination
• Matches original shape to ensure proper fit and clearance around the igniter

• Disconnect power to the appliance (and shut off gas if applicable) before servicing
• Allow the oven to cool completely and wear gloves to avoid cuts from sheet metal
• Handle the igniter and cover carefully; avoid touching the igniter surface directly
• Test appliance operation after reinstall

This orifice spud meters gas to a burner in your range or cooktop. Replacing a clogged or damaged spud helps restore correct flame size and reliable ignition for consistent cooking performance.

• Regulates gas flow from the valve to the burner head for proper combustion
• Helps restore consistent flame height and even heating on the burner
• Sized for the burner rating and fuel type specified by your model; always match the correct part

• Disconnect power and shut off gas supply; allow the appliance to cool completely before servicing.
• Access the burner orifice and replace with the correct, model-specified spud using an appropriate wrench; do not overtighten.
• Restore gas and check all connections for leaks with a soap-and-water solution.
• Use only the spud specified for your fuel type (NG or LP); do not attempt conversion without the approved kit and instructions.

The Orifice Spud is an OEM part for GE ranges and cooktops. It is a small, precise component responsible for regulating the flow of gas to the burner, ensuring a controlled and efficient flame for cooking. This spud is essential for maintaining the correct gas pressure and flame size.

Over time, orifice spuds can become clogged or damaged due to residue buildup, corrosion, or improper cleaning. These issues can lead to inefficient burner performance or safety hazards.

Symptoms of a bad orifice spud include:

• Uneven or weak burner flames
• Difficulty in igniting the burner
• Yellow or flickering flames
• Gas odors near the burner area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Burner Valve Assembly 270 is an OEM part for GE gas ranges. It controls gas flow to individual burners to deliver precise heating levels.  

Causes of a bad burner valve assembly include worn rubber diaphragms, debris inside valve channels, or damage from repeated heating cycles.

Symptoms are:

• Uneven cooking temperatures across burners
• Inability to ignite or adjust certain burners  
• Fluctuations in flame height/cooking output

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

The Valve Burner is an OEM component for GE gas ranges. Located below the grates atop each cooktop burner, it precisely mixes gas and air to provide controllable flames. A valve adjusts gas flow while perforated metal distributes the flame evenly. 

Symptoms of a faulty valve burner include: 

• Difficulty obtaining or maintaining set flame levels  
• Unstable or intermittent burner operation
• Yellow fire or flame that produces excessive soot
• No ignition or fire when the knob is turned

Causes can be wear of internal valve components, debris, or clogs in gas ports restricting flow over time. Damage from spills or dropped objects may also crack the burner.

This OEM GE burner is also compatible with models from Hotpoint and RCA.

The Burner Valve Assembly 3R 310 is an OEM part for GE gas ranges. It controls gas flow to individual burners to deliver precise heating levels.  

Causes of a bad burner valve assembly include worn rubber diaphragms, debris inside valve channels, or damage from repeated heating cycles.

Symptoms are:

• Uneven cooking temperatures across burners
• Inability to ignite or adjust certain burners  
• Fluctuations in flame height/cooking output

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This 10-32 machine screw secures brackets, panels, and other hardware in cooking appliances. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned and safely fastened. What it does:

• Fastens panels, brackets, and components using a 10-32 machine thread
• Replaces hardware that is missing, rusted, or stripped
• Helps address loose or rattling parts and minor panel misalignment
• Maintains secure mounting after service or part replacement

• One 10-32 machine screw

• Disconnect power; for gas appliances, also shut off gas before service
• Support the panel or bracket while removing/installing hardware
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace them one at a time to keep alignment

This factory screw secures components on GE cooking appliances. Replacing a lost or stripped fastener helps keep parts tight and aligned for safer, rattle-free operation.

• Fastens brackets, panels, trim, or burner components on a range, cooktop, or wall oven
• Replaces missing, corroded, or stripped hardware
• Helps reduce looseness, vibration, or rattling noises
• Restores proper alignment after service or cleaning

• Disconnect power and shut off gas supply. Allow the appliance to cool completely.
• Match this screw to the original and install in the same location.
• Use the correct driver; hand-tighten and avoid overtightening to prevent stripped threads or cracked parts.
• If mating threads are damaged, repair or replace the affected component before reassembly.

This part is a spark electrode. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a defective or burnt-out spark electrode on multiple different models of ovens and stoves.This spark electrode catches the stream of gas emitted from the burner alight in order to start the stove's flame. Spark electrodes are a common component on newer gas range models. Over time, this part may burn out or become damaged, which will prevent the burner flame from lighting. This part requires proper tools for replacement. Before starting, disconnect the stove completely from both power and gas hookups. Please follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install this spark electrode, the appropriate owner's manual and included diagrams should be referred to.As an authentic replacement part, this spark electrode is suitable for use on several different models of gas-powered ovens, stoves, and ranges manufactured by General Electric and Hotpoint. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This valve control assembly regulates gas flow to the burner, restoring safe and reliable ignition and heating. Replace a faulty valve control to return proper burner operation and consistent heat output. What it does:

• Controls gas flow to the burner so the appliance can ignite and hold a flame
• Helps the burner reach and maintain proper heat during operation
• Can resolve symptoms like burners not lighting, weak or no flame, or intermittent heating
• Works as the control interface between the appliance's control system and the gas supply

• One valve control assembly

• Turn off gas supply and disconnect power before starting any repair
• Handle the assembly carefully and avoid forcing connectors; ensure wiring and gas fittings are secure
• If you smell gas or suspect a leak after installation, stop immediately
• Follow the appliance manufacturer's service manual for model-specific installation steps and torque specs

The Igniter Glow Bar is an OEM part for GE gas ovens and ranges. It is responsible for igniting the gas by heating up to a high temperature, which then lights the gas burner to start the cooking process.

You should replace the igniter glow bar if it becomes faulty or fails to ignite the gas. Common causes of a bad igniter glow bar include wear and tear from frequent use, electrical issues, or physical damage to the igniter element.

Symptoms of a bad igniter glow bar include:

• The oven not heating up
• The gas burners not igniting
• A clicking sound without ignition
• Visible cracks or damage to the igniter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Oven Igniter is an OEM replacement part for GE ovens, designed to ignite the bake igniter to start the heating process. This part is responsible for creating the spark that ignites the gas, providing the heat needed to cook and bake food. Over time, the oven igniter can wear out or become damaged, which can prevent the oven from heating.

Symptoms of a bad Oven Igniter include:

• The oven not heating up at all.
• The oven taking longer than normal to heat.
• Gas smell in the oven due to gas being released without ignition.
• A clicking sound without the oven igniting.

Causes of a bad igniter can include normal wear and tear over time, exposure to excessive heat or moisture, or physical damage from impact or mishandling.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

IMPORTANT: The connector plug may need to be cut off and igniter wires connected to range wires using porcelain wire connectors.

Package of 12

This valve lockout mounting clip secures the appliance's gas valve actuator to help prevent unintended valve movement and ensure consistent operation. It replaces a worn or broken lockout clip to restore reliable valve positioning. What it does:

• Secures the gas valve actuator or linkage to keep the valve in its intended position
• Helps stop intermittent or loose valve movement that can cause inconsistent ignition or burner operation
• Restores proper mechanical alignment after the original clip has cracked, bent, or broken
• Small replacement part used where a damaged lockout clip prevents stable valve function

• One valve lockout mounting clip

• Disconnect power and shut off gas supply before servicing; follow all safety precautions
• Inspect adjacent fasteners and actuator for damage; replace any additional damaged parts as needed
• Basic hand tools typically required; handle small plastic clips carefully to avoid breakage

This silicon controlled rectifier (SCR) switches and regulates power to heating elements and motors in compatible appliances, restoring controlled current flow for proper operation. It's a direct-replacement electronic switching component. What it does:

• Acts as a solid-state switch to control AC power to heater or motor circuits
• Helps regulate current during timed or thermostatic cycles
• Common replacement when appliance shows intermittent heating, no heat, or erratic motor control
• Replaces a failed/shorted SCR that can cause blown fuses or control board errors

• One silicon controlled rectifier (single SCR)

• Intended for technicians or experienced DIYers; disconnect power before servicing
• Verify correct SCR orientation and secure the 8-32 screw terminal; avoid overtightening
• Observe ESD precautions and handle the part by non-conductive areas